12V Digital Thermometer Temperature Controller Dual Relay Alarm Air Re

12V Digital Thermometer Temperature Controller Dual Relay Alarm Air Regulator

SKU:011968

$9.99

Description

Temperature range: -20 ℃ ~ + 100 ℃
Resolution: -9.9 ℃ ~ 99.9 ℃ paragraph 0.1 ℃, other temperature ranges 1 ℃
Temperature measurement accuracy: 1 ℃
Minimum temperature difference: 0.1 ℃
Refresh rate about: 0.5S
Input Power: DC 12V
Measuring input: 1 m NTC (10K 0.5%) alloy waterproof sensor
Output: Two relay 10A
Environmental requirements: -10 ℃ ~ + 60 ℃ Humidity 20% to 75%
Size: 70mm * 39mm

Intelligent dual temperature control relay instructions

Tips: Set the temperature when the buyer must ensure that the upper limit temperature is greater than the lower limit temperature, the system will work properly.
Circuit connection: Connect the power supply with reference to the circuit diagram and load, the temperature sensor is missing or damaged digital tube will show "- - -", before using buyer must check the temperature sensor is installed.
The temperature output 10A relay, to meet a variety of high-power load, make sure that the line is correct.
LEDs, LED status descriptions:
LED: Off indicates the relay off, ON means the relay is closed
Digital: Display "- - -", 1, check the temperature sensor 2 is missing or damaged, heating mode, high temperature protection 3, cryogenic cooling mode protection. In protected mode relay automatically disconnected.
Use keys: temperature control panel has three buttons, button + button - SET button
Button +: Achieving Rapid accumulation value
Key: - fast diminishing value
SET key SET: Temperature set temperature and operating mode interface query interface parameter setting interface
During the SET press SET press according to different times, the corresponding digital temperature limit will be blinking, you can set the upper and lower temperature through the key addition and subtraction. After setting 8s automatically save data or short press three times data can be saved.
SET Press to enter the actual temperature and the operating mode query interface, digital (on) the actual measured temperature. Digital (lower) showing the operation mode. L represents the lower limit temperature below the set temperature, H is the upper limit temperature is higher than the temperature setting, OFF indicates when the temperature is between the upper and lower limits, the relay is in the off state.
Mode setting: Setting the temperature 1: temperature upper limit set temperature 2: lower limit temperature
Example applications: now the upper limit temperature to 40.0 ℃, the minimum temperature is set to 20.0 ℃. At different temperature ranges relay operate as follows:
When the actual temperature> 40 ℃, the relay 1 is closed, the relay 2 release;
When the actual temperature of 20 ℃ ≤ ≤40 ℃ release relay 1, relay 2 release;
When the actual temperature <20 ℃, the relay 2 is closed, the relay 1 release.
Parameter settings: the need for the user parameter settings must first hold the SET button and then give the thermostat power, to enter the parameter setting interface. There are three sets of parameters P0-P2 can be used for user settings.
Parameter setting item

Function Description Setting range Factory setting

P0 temperature correction -10 ℃ ~ + 10 ℃ 0
P1 limit relay time 0 ~ 999s OFF
P2 lower limit relay time 0 ~ 999s OFF

friendly reminder:

P1 = OFF: indicates the actual temperature exceeds the upper limit temperature, corresponding relay will remain energized (long attracted state).
P1 = 1 ~ 999: indicates the actual temperature exceeds the upper limit temperature, corresponding relay will energize long, then stop (Jog attracted state).
P2 = OFF: indicates the actual temperature is below the lower limit temperature, corresponding relay will remain energized (long attracted state).
P2 = 1 ~ 999: indicates the actual temperature is below the lower limit temperature, corresponding relay will energize long, then stop (Jog attracted state).

Package Inclued

1PCS 12V Digital Dual Relay Alarm Thermometer Temperature Controller Air Regulator

Quantity

guaranteeQuality checked
Special gift cardsSpecial gift cards
Free return Within 60 days
Consultancy86-0755-85201155

Description

Temperature range: -20 ℃ ~ + 100 ℃
Resolution: -9.9 ℃ ~ 99.9 ℃ paragraph 0.1 ℃, other temperature ranges 1 ℃
Temperature measurement accuracy: 1 ℃
Minimum temperature difference: 0.1 ℃
Refresh rate about: 0.5S
Input Power: DC 12V
Measuring input: 1 m NTC (10K 0.5%) alloy waterproof sensor
Output: Two relay 10A
Environmental requirements: -10 ℃ ~ + 60 ℃ Humidity 20% to 75%
Size: 70mm * 39mm

Intelligent dual temperature control relay instructions

Tips: Set the temperature when the buyer must ensure that the upper limit temperature is greater than the lower limit temperature, the system will work properly.
Circuit connection: Connect the power supply with reference to the circuit diagram and load, the temperature sensor is missing or damaged digital tube will show "- - -", before using buyer must check the temperature sensor is installed.
The temperature output 10A relay, to meet a variety of high-power load, make sure that the line is correct.
LEDs, LED status descriptions:
LED: Off indicates the relay off, ON means the relay is closed
Digital: Display "- - -", 1, check the temperature sensor 2 is missing or damaged, heating mode, high temperature protection 3, cryogenic cooling mode protection. In protected mode relay automatically disconnected.
Use keys: temperature control panel has three buttons, button + button - SET button
Button +: Achieving Rapid accumulation value
Key: - fast diminishing value
SET key SET: Temperature set temperature and operating mode interface query interface parameter setting interface
During the SET press SET press according to different times, the corresponding digital temperature limit will be blinking, you can set the upper and lower temperature through the key addition and subtraction. After setting 8s automatically save data or short press three times data can be saved.
SET Press to enter the actual temperature and the operating mode query interface, digital (on) the actual measured temperature. Digital (lower) showing the operation mode. L represents the lower limit temperature below the set temperature, H is the upper limit temperature is higher than the temperature setting, OFF indicates when the temperature is between the upper and lower limits, the relay is in the off state.
Mode setting: Setting the temperature 1: temperature upper limit set temperature 2: lower limit temperature
Example applications: now the upper limit temperature to 40.0 ℃, the minimum temperature is set to 20.0 ℃. At different temperature ranges relay operate as follows:
When the actual temperature> 40 ℃, the relay 1 is closed, the relay 2 release;
When the actual temperature of 20 ℃ ≤ ≤40 ℃ release relay 1, relay 2 release;
When the actual temperature <20 ℃, the relay 2 is closed, the relay 1 release.
Parameter settings: the need for the user parameter settings must first hold the SET button and then give the thermostat power, to enter the parameter setting interface. There are three sets of parameters P0-P2 can be used for user settings.
Parameter setting item

Function Description Setting range Factory setting

P0 temperature correction -10 ℃ ~ + 10 ℃ 0
P1 limit relay time 0 ~ 999s OFF
P2 lower limit relay time 0 ~ 999s OFF

friendly reminder:

P1 = OFF: indicates the actual temperature exceeds the upper limit temperature, corresponding relay will remain energized (long attracted state).
P1 = 1 ~ 999: indicates the actual temperature exceeds the upper limit temperature, corresponding relay will energize long, then stop (Jog attracted state).
P2 = OFF: indicates the actual temperature is below the lower limit temperature, corresponding relay will remain energized (long attracted state).
P2 = 1 ~ 999: indicates the actual temperature is below the lower limit temperature, corresponding relay will energize long, then stop (Jog attracted state).

Package Inclued

1PCS 12V Digital Dual Relay Alarm Thermometer Temperature Controller Air Regulator

Manual

Purchasing & Delivery

Before you make your purchase, it’s helpful to know the measurements of the area you plan to place the furniture. You should also measure any doorways and hallways through which the furniture will pass to get to its final destination.

Picking up at the store

Shopify Shop requires that all products are properly inspected BEFORE you take it home to insure there are no surprises. Our team is happy to open all packages and will assist in the inspection process. We will then reseal packages for safe transport. We encourage all customers to bring furniture pads or blankets to protect the items during transport as well as rope or tie downs. Shopify Shop will not be responsible for damage that occurs after leaving the store or during transit. It is the purchaser’s responsibility to make sure the correct items are picked up and in good condition.

Delivery

Customers are able to pick the next available delivery day that best fits their schedule. However, to route stops as efficiently as possible, Shopify Shop will provide the time frame. Customers will not be able to choose a time. You will be notified in advance of your scheduled time frame. Please make sure that a responsible adult (18 years or older) will be home at that time.
In preparation for your delivery, please remove existing furniture, pictures, mirrors, accessories, etc. to prevent damages. Also insure that the area where you would like your furniture placed is clear of any old furniture and any other items that may obstruct the passageway of the delivery team. Shopify Shop will deliver, assemble, and set-up your new furniture purchase and remove all packing materials from your home. Our delivery crews are not permitted to move your existing furniture or other household items. Delivery personnel will attempt to deliver the purchased items in a safe and controlled manner but will not attempt to place furniture if they feel it will result in damage to the product or your home. Delivery personnel are unable to remove doors, hoist furniture or carry furniture up more than 3 flights of stairs. An elevator must be available for deliveries to the 4th floor and above.

Other Customers also buy:

$2 Wire 0.56\" Voltmeter LED Tube Digital DC4.5/4.7/5V-30V Voltage Panel Meter$

2 Wire 0.56\" Voltmeter LED Tube Digital DC4.5/4.7/5V-30V Voltage Panel Meter

Translation missing: en.products.product.regular_price $5.99
{"id":4792266784839,"title":"12V Digital Thermometer Temperature Controller Dual Relay Alarm Air Regulator","handle":"12v-digital-thermometer-temperature-controller-dual-relay-alarm-air-regulator","description":"\u003cstrong\u003eDescription\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eTemperature range: -20 ℃ ~ + 100 ℃\u003c\/li\u003e\n\u003cli\u003eResolution: -9.9 ℃ ~ 99.9 ℃ paragraph 0.1 ℃, other temperature ranges 1 ℃\u003c\/li\u003e\n\u003cli\u003eTemperature measurement accuracy: 1 ℃\u003c\/li\u003e\n\u003cli\u003eMinimum temperature difference: 0.1 ℃\u003c\/li\u003e\n\u003cli\u003eRefresh rate about: 0.5S\u003c\/li\u003e\n\u003cli\u003eInput Power: DC 12V\u003c\/li\u003e\n\u003cli\u003eMeasuring input: 1 m NTC (10K 0.5%) alloy waterproof sensor\u003c\/li\u003e\n\u003cli\u003eOutput: Two relay 10A\u003c\/li\u003e\n\u003cli\u003eEnvironmental requirements: -10 ℃ ~ + 60 ℃ Humidity 20% to 75%\u003c\/li\u003e\n\u003cli\u003eSize: 70mm * 39mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003eIntelligent dual temperature control relay instructions\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eTips: Set the temperature when the buyer must ensure that the upper limit temperature is greater than the lower limit temperature, the system will work properly.\u003c\/li\u003e\n\u003cli\u003eCircuit connection: Connect the power supply with reference to the circuit diagram and load, the temperature sensor is missing or damaged digital tube will show \"- - -\", before using buyer must check the temperature sensor is installed.\u003c\/li\u003e\n\u003cli\u003eThe temperature output 10A relay, to meet a variety of high-power load, make sure that the line is correct.\u003c\/li\u003e\n\u003cli\u003eLEDs, LED status descriptions:\u003c\/li\u003e\n\u003cli\u003eLED: Off indicates the relay off, ON means the relay is closed\u003c\/li\u003e\n\u003cli\u003eDigital: Display \"- - -\", 1, check the temperature sensor 2 is missing or damaged, heating mode, high temperature protection 3, cryogenic cooling mode protection. In protected mode relay automatically disconnected.\u003c\/li\u003e\n\u003cli\u003eUse keys: temperature control panel has three buttons, button + button - SET button\u003c\/li\u003e\n\u003cli\u003eButton +: Achieving Rapid accumulation value\u003c\/li\u003e\n\u003cli\u003eKey: - fast diminishing value\u003c\/li\u003e\n\u003cli\u003eSET key SET: Temperature set temperature and operating mode interface query interface parameter setting interface\u003c\/li\u003e\n\u003cli\u003eDuring the SET press SET press according to different times, the corresponding digital temperature limit will be blinking, you can set the upper and lower temperature through the key addition and subtraction. After setting 8s automatically save data or short press three times data can be saved.\u003c\/li\u003e\n\u003cli\u003eSET Press to enter the actual temperature and the operating mode query interface, digital (on) the actual measured temperature. Digital (lower) showing the operation mode. L represents the lower limit temperature below the set temperature, H is the upper limit temperature is higher than the temperature setting, OFF indicates when the temperature is between the upper and lower limits, the relay is in the off state.\u003c\/li\u003e\n\u003cli\u003eMode setting: Setting the temperature 1: temperature upper limit set temperature 2: lower limit temperature\u003c\/li\u003e\n\u003cli\u003eExample applications: now the upper limit temperature to 40.0 ℃, the minimum temperature is set to 20.0 ℃. At different temperature ranges relay operate as follows:\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature\u0026gt; 40 ℃, the relay 1 is closed, the relay 2 release;\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature of 20 ℃ ≤ ≤40 ℃ release relay 1, relay 2 release;\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature \u0026lt;20 ℃, the relay 2 is closed, the relay 1 release.\u003c\/li\u003e\n\u003cli\u003eParameter settings: the need for the user parameter settings must first hold the SET button and then give the thermostat power, to enter the parameter setting interface. There are three sets of parameters P0-P2 can be used for user settings.\u003c\/li\u003e\n\u003cli\u003eParameter setting item\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003eFunction Description Setting range Factory setting\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eP0 temperature correction -10 ℃ ~ + 10 ℃ 0\u003c\/li\u003e\n\u003cli\u003eP1 limit relay time 0 ~ 999s OFF\u003c\/li\u003e\n\u003cli\u003eP2 lower limit relay time 0 ~ 999s OFF\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003efriendly reminder:\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eP1 = OFF: indicates the actual temperature exceeds the upper limit temperature, corresponding relay will remain energized (long attracted state).\u003c\/li\u003e\n\u003cli\u003eP1 = 1 ~ 999: indicates the actual temperature exceeds the upper limit temperature, corresponding relay will energize long, then stop (Jog attracted state).\u003c\/li\u003e\n\u003cli\u003eP2 = OFF: indicates the actual temperature is below the lower limit temperature, corresponding relay will remain energized (long attracted state).\u003c\/li\u003e\n\u003cli\u003eP2 = 1 ~ 999: indicates the actual temperature is below the lower limit temperature, corresponding relay will energize long, then stop (Jog attracted state).\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003ePackage Inclued\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003e1PCS 12V Digital Dual Relay Alarm Thermometer Temperature Controller Air Regulator\u003c\/li\u003e\n\u003c\/ul\u003e","published_at":"2020-08-14T11:39:05+08:00","created_at":"2020-08-14T11:39:03+08:00","vendor":"DIYMORE","type":"","tags":[],"price":999,"price_min":999,"price_max":999,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":32508226568263,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"011968","requires_shipping":true,"taxable":false,"featured_image":null,"available":true,"name":"12V Digital Thermometer Temperature Controller Dual Relay Alarm Air Regulator","public_title":null,"options":["Default Title"],"price":999,"weight":0,"compare_at_price":null,"inventory_management":"shopify","barcode":"","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/www.diymore.cc\/cdn\/shop\/products\/011968_1.jpg?v=1597376346","\/\/www.diymore.cc\/cdn\/shop\/products\/011968_3.jpg?v=1597376346","\/\/www.diymore.cc\/cdn\/shop\/products\/011968_2.jpg?v=1597376346","\/\/www.diymore.cc\/cdn\/shop\/products\/011968_4.jpg?v=1597376346","\/\/www.diymore.cc\/cdn\/shop\/products\/011968_6.jpg?v=1597376346","\/\/www.diymore.cc\/cdn\/shop\/products\/011968_5.jpg?v=1597376346"],"featured_image":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_1.jpg?v=1597376346","options":["Title"],"media":[{"alt":null,"id":7280857022535,"position":1,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_1.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_1.jpg?v=1597376346","width":1000},{"alt":null,"id":7280857055303,"position":2,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_3.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_3.jpg?v=1597376346","width":1000},{"alt":null,"id":7280857088071,"position":3,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_2.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_2.jpg?v=1597376346","width":1000},{"alt":null,"id":7280857120839,"position":4,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_4.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_4.jpg?v=1597376346","width":1000},{"alt":null,"id":7280857153607,"position":5,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_6.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_6.jpg?v=1597376346","width":1000},{"alt":null,"id":7280857186375,"position":6,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_5.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_5.jpg?v=1597376346","width":1000}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cstrong\u003eDescription\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eTemperature range: -20 ℃ ~ + 100 ℃\u003c\/li\u003e\n\u003cli\u003eResolution: -9.9 ℃ ~ 99.9 ℃ paragraph 0.1 ℃, other temperature ranges 1 ℃\u003c\/li\u003e\n\u003cli\u003eTemperature measurement accuracy: 1 ℃\u003c\/li\u003e\n\u003cli\u003eMinimum temperature difference: 0.1 ℃\u003c\/li\u003e\n\u003cli\u003eRefresh rate about: 0.5S\u003c\/li\u003e\n\u003cli\u003eInput Power: DC 12V\u003c\/li\u003e\n\u003cli\u003eMeasuring input: 1 m NTC (10K 0.5%) alloy waterproof sensor\u003c\/li\u003e\n\u003cli\u003eOutput: Two relay 10A\u003c\/li\u003e\n\u003cli\u003eEnvironmental requirements: -10 ℃ ~ + 60 ℃ Humidity 20% to 75%\u003c\/li\u003e\n\u003cli\u003eSize: 70mm * 39mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003eIntelligent dual temperature control relay instructions\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eTips: Set the temperature when the buyer must ensure that the upper limit temperature is greater than the lower limit temperature, the system will work properly.\u003c\/li\u003e\n\u003cli\u003eCircuit connection: Connect the power supply with reference to the circuit diagram and load, the temperature sensor is missing or damaged digital tube will show \"- - -\", before using buyer must check the temperature sensor is installed.\u003c\/li\u003e\n\u003cli\u003eThe temperature output 10A relay, to meet a variety of high-power load, make sure that the line is correct.\u003c\/li\u003e\n\u003cli\u003eLEDs, LED status descriptions:\u003c\/li\u003e\n\u003cli\u003eLED: Off indicates the relay off, ON means the relay is closed\u003c\/li\u003e\n\u003cli\u003eDigital: Display \"- - -\", 1, check the temperature sensor 2 is missing or damaged, heating mode, high temperature protection 3, cryogenic cooling mode protection. In protected mode relay automatically disconnected.\u003c\/li\u003e\n\u003cli\u003eUse keys: temperature control panel has three buttons, button + button - SET button\u003c\/li\u003e\n\u003cli\u003eButton +: Achieving Rapid accumulation value\u003c\/li\u003e\n\u003cli\u003eKey: - fast diminishing value\u003c\/li\u003e\n\u003cli\u003eSET key SET: Temperature set temperature and operating mode interface query interface parameter setting interface\u003c\/li\u003e\n\u003cli\u003eDuring the SET press SET press according to different times, the corresponding digital temperature limit will be blinking, you can set the upper and lower temperature through the key addition and subtraction. After setting 8s automatically save data or short press three times data can be saved.\u003c\/li\u003e\n\u003cli\u003eSET Press to enter the actual temperature and the operating mode query interface, digital (on) the actual measured temperature. Digital (lower) showing the operation mode. L represents the lower limit temperature below the set temperature, H is the upper limit temperature is higher than the temperature setting, OFF indicates when the temperature is between the upper and lower limits, the relay is in the off state.\u003c\/li\u003e\n\u003cli\u003eMode setting: Setting the temperature 1: temperature upper limit set temperature 2: lower limit temperature\u003c\/li\u003e\n\u003cli\u003eExample applications: now the upper limit temperature to 40.0 ℃, the minimum temperature is set to 20.0 ℃. At different temperature ranges relay operate as follows:\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature\u0026gt; 40 ℃, the relay 1 is closed, the relay 2 release;\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature of 20 ℃ ≤ ≤40 ℃ release relay 1, relay 2 release;\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature \u0026lt;20 ℃, the relay 2 is closed, the relay 1 release.\u003c\/li\u003e\n\u003cli\u003eParameter settings: the need for the user parameter settings must first hold the SET button and then give the thermostat power, to enter the parameter setting interface. There are three sets of parameters P0-P2 can be used for user settings.\u003c\/li\u003e\n\u003cli\u003eParameter setting item\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003eFunction Description Setting range Factory setting\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eP0 temperature correction -10 ℃ ~ + 10 ℃ 0\u003c\/li\u003e\n\u003cli\u003eP1 limit relay time 0 ~ 999s OFF\u003c\/li\u003e\n\u003cli\u003eP2 lower limit relay time 0 ~ 999s OFF\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003efriendly reminder:\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eP1 = OFF: indicates the actual temperature exceeds the upper limit temperature, corresponding relay will remain energized (long attracted state).\u003c\/li\u003e\n\u003cli\u003eP1 = 1 ~ 999: indicates the actual temperature exceeds the upper limit temperature, corresponding relay will energize long, then stop (Jog attracted state).\u003c\/li\u003e\n\u003cli\u003eP2 = OFF: indicates the actual temperature is below the lower limit temperature, corresponding relay will remain energized (long attracted state).\u003c\/li\u003e\n\u003cli\u003eP2 = 1 ~ 999: indicates the actual temperature is below the lower limit temperature, corresponding relay will energize long, then stop (Jog attracted state).\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003ePackage Inclued\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003e1PCS 12V Digital Dual Relay Alarm Thermometer Temperature Controller Air Regulator\u003c\/li\u003e\n\u003c\/ul\u003e"}
18650 Battery Shield V8 Mobile Power Bank 3V/5V for Arduino ESP32 ESP8266

Translation missing: en.products.product.regular_price $5.99
{"id":4792266784839,"title":"12V Digital Thermometer Temperature Controller Dual Relay Alarm Air Regulator","handle":"12v-digital-thermometer-temperature-controller-dual-relay-alarm-air-regulator","description":"\u003cstrong\u003eDescription\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eTemperature range: -20 ℃ ~ + 100 ℃\u003c\/li\u003e\n\u003cli\u003eResolution: -9.9 ℃ ~ 99.9 ℃ paragraph 0.1 ℃, other temperature ranges 1 ℃\u003c\/li\u003e\n\u003cli\u003eTemperature measurement accuracy: 1 ℃\u003c\/li\u003e\n\u003cli\u003eMinimum temperature difference: 0.1 ℃\u003c\/li\u003e\n\u003cli\u003eRefresh rate about: 0.5S\u003c\/li\u003e\n\u003cli\u003eInput Power: DC 12V\u003c\/li\u003e\n\u003cli\u003eMeasuring input: 1 m NTC (10K 0.5%) alloy waterproof sensor\u003c\/li\u003e\n\u003cli\u003eOutput: Two relay 10A\u003c\/li\u003e\n\u003cli\u003eEnvironmental requirements: -10 ℃ ~ + 60 ℃ Humidity 20% to 75%\u003c\/li\u003e\n\u003cli\u003eSize: 70mm * 39mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003eIntelligent dual temperature control relay instructions\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eTips: Set the temperature when the buyer must ensure that the upper limit temperature is greater than the lower limit temperature, the system will work properly.\u003c\/li\u003e\n\u003cli\u003eCircuit connection: Connect the power supply with reference to the circuit diagram and load, the temperature sensor is missing or damaged digital tube will show \"- - -\", before using buyer must check the temperature sensor is installed.\u003c\/li\u003e\n\u003cli\u003eThe temperature output 10A relay, to meet a variety of high-power load, make sure that the line is correct.\u003c\/li\u003e\n\u003cli\u003eLEDs, LED status descriptions:\u003c\/li\u003e\n\u003cli\u003eLED: Off indicates the relay off, ON means the relay is closed\u003c\/li\u003e\n\u003cli\u003eDigital: Display \"- - -\", 1, check the temperature sensor 2 is missing or damaged, heating mode, high temperature protection 3, cryogenic cooling mode protection. In protected mode relay automatically disconnected.\u003c\/li\u003e\n\u003cli\u003eUse keys: temperature control panel has three buttons, button + button - SET button\u003c\/li\u003e\n\u003cli\u003eButton +: Achieving Rapid accumulation value\u003c\/li\u003e\n\u003cli\u003eKey: - fast diminishing value\u003c\/li\u003e\n\u003cli\u003eSET key SET: Temperature set temperature and operating mode interface query interface parameter setting interface\u003c\/li\u003e\n\u003cli\u003eDuring the SET press SET press according to different times, the corresponding digital temperature limit will be blinking, you can set the upper and lower temperature through the key addition and subtraction. After setting 8s automatically save data or short press three times data can be saved.\u003c\/li\u003e\n\u003cli\u003eSET Press to enter the actual temperature and the operating mode query interface, digital (on) the actual measured temperature. Digital (lower) showing the operation mode. L represents the lower limit temperature below the set temperature, H is the upper limit temperature is higher than the temperature setting, OFF indicates when the temperature is between the upper and lower limits, the relay is in the off state.\u003c\/li\u003e\n\u003cli\u003eMode setting: Setting the temperature 1: temperature upper limit set temperature 2: lower limit temperature\u003c\/li\u003e\n\u003cli\u003eExample applications: now the upper limit temperature to 40.0 ℃, the minimum temperature is set to 20.0 ℃. At different temperature ranges relay operate as follows:\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature\u0026gt; 40 ℃, the relay 1 is closed, the relay 2 release;\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature of 20 ℃ ≤ ≤40 ℃ release relay 1, relay 2 release;\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature \u0026lt;20 ℃, the relay 2 is closed, the relay 1 release.\u003c\/li\u003e\n\u003cli\u003eParameter settings: the need for the user parameter settings must first hold the SET button and then give the thermostat power, to enter the parameter setting interface. There are three sets of parameters P0-P2 can be used for user settings.\u003c\/li\u003e\n\u003cli\u003eParameter setting item\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003eFunction Description Setting range Factory setting\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eP0 temperature correction -10 ℃ ~ + 10 ℃ 0\u003c\/li\u003e\n\u003cli\u003eP1 limit relay time 0 ~ 999s OFF\u003c\/li\u003e\n\u003cli\u003eP2 lower limit relay time 0 ~ 999s OFF\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003efriendly reminder:\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eP1 = OFF: indicates the actual temperature exceeds the upper limit temperature, corresponding relay will remain energized (long attracted state).\u003c\/li\u003e\n\u003cli\u003eP1 = 1 ~ 999: indicates the actual temperature exceeds the upper limit temperature, corresponding relay will energize long, then stop (Jog attracted state).\u003c\/li\u003e\n\u003cli\u003eP2 = OFF: indicates the actual temperature is below the lower limit temperature, corresponding relay will remain energized (long attracted state).\u003c\/li\u003e\n\u003cli\u003eP2 = 1 ~ 999: indicates the actual temperature is below the lower limit temperature, corresponding relay will energize long, then stop (Jog attracted state).\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003ePackage Inclued\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003e1PCS 12V Digital Dual Relay Alarm Thermometer Temperature Controller Air Regulator\u003c\/li\u003e\n\u003c\/ul\u003e","published_at":"2020-08-14T11:39:05+08:00","created_at":"2020-08-14T11:39:03+08:00","vendor":"DIYMORE","type":"","tags":[],"price":999,"price_min":999,"price_max":999,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":32508226568263,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"011968","requires_shipping":true,"taxable":false,"featured_image":null,"available":true,"name":"12V Digital Thermometer Temperature Controller Dual Relay Alarm Air Regulator","public_title":null,"options":["Default Title"],"price":999,"weight":0,"compare_at_price":null,"inventory_management":"shopify","barcode":"","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/www.diymore.cc\/cdn\/shop\/products\/011968_1.jpg?v=1597376346","\/\/www.diymore.cc\/cdn\/shop\/products\/011968_3.jpg?v=1597376346","\/\/www.diymore.cc\/cdn\/shop\/products\/011968_2.jpg?v=1597376346","\/\/www.diymore.cc\/cdn\/shop\/products\/011968_4.jpg?v=1597376346","\/\/www.diymore.cc\/cdn\/shop\/products\/011968_6.jpg?v=1597376346","\/\/www.diymore.cc\/cdn\/shop\/products\/011968_5.jpg?v=1597376346"],"featured_image":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_1.jpg?v=1597376346","options":["Title"],"media":[{"alt":null,"id":7280857022535,"position":1,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_1.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_1.jpg?v=1597376346","width":1000},{"alt":null,"id":7280857055303,"position":2,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_3.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_3.jpg?v=1597376346","width":1000},{"alt":null,"id":7280857088071,"position":3,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_2.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_2.jpg?v=1597376346","width":1000},{"alt":null,"id":7280857120839,"position":4,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_4.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_4.jpg?v=1597376346","width":1000},{"alt":null,"id":7280857153607,"position":5,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_6.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_6.jpg?v=1597376346","width":1000},{"alt":null,"id":7280857186375,"position":6,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_5.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_5.jpg?v=1597376346","width":1000}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cstrong\u003eDescription\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eTemperature range: -20 ℃ ~ + 100 ℃\u003c\/li\u003e\n\u003cli\u003eResolution: -9.9 ℃ ~ 99.9 ℃ paragraph 0.1 ℃, other temperature ranges 1 ℃\u003c\/li\u003e\n\u003cli\u003eTemperature measurement accuracy: 1 ℃\u003c\/li\u003e\n\u003cli\u003eMinimum temperature difference: 0.1 ℃\u003c\/li\u003e\n\u003cli\u003eRefresh rate about: 0.5S\u003c\/li\u003e\n\u003cli\u003eInput Power: DC 12V\u003c\/li\u003e\n\u003cli\u003eMeasuring input: 1 m NTC (10K 0.5%) alloy waterproof sensor\u003c\/li\u003e\n\u003cli\u003eOutput: Two relay 10A\u003c\/li\u003e\n\u003cli\u003eEnvironmental requirements: -10 ℃ ~ + 60 ℃ Humidity 20% to 75%\u003c\/li\u003e\n\u003cli\u003eSize: 70mm * 39mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003eIntelligent dual temperature control relay instructions\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eTips: Set the temperature when the buyer must ensure that the upper limit temperature is greater than the lower limit temperature, the system will work properly.\u003c\/li\u003e\n\u003cli\u003eCircuit connection: Connect the power supply with reference to the circuit diagram and load, the temperature sensor is missing or damaged digital tube will show \"- - -\", before using buyer must check the temperature sensor is installed.\u003c\/li\u003e\n\u003cli\u003eThe temperature output 10A relay, to meet a variety of high-power load, make sure that the line is correct.\u003c\/li\u003e\n\u003cli\u003eLEDs, LED status descriptions:\u003c\/li\u003e\n\u003cli\u003eLED: Off indicates the relay off, ON means the relay is closed\u003c\/li\u003e\n\u003cli\u003eDigital: Display \"- - -\", 1, check the temperature sensor 2 is missing or damaged, heating mode, high temperature protection 3, cryogenic cooling mode protection. In protected mode relay automatically disconnected.\u003c\/li\u003e\n\u003cli\u003eUse keys: temperature control panel has three buttons, button + button - SET button\u003c\/li\u003e\n\u003cli\u003eButton +: Achieving Rapid accumulation value\u003c\/li\u003e\n\u003cli\u003eKey: - fast diminishing value\u003c\/li\u003e\n\u003cli\u003eSET key SET: Temperature set temperature and operating mode interface query interface parameter setting interface\u003c\/li\u003e\n\u003cli\u003eDuring the SET press SET press according to different times, the corresponding digital temperature limit will be blinking, you can set the upper and lower temperature through the key addition and subtraction. After setting 8s automatically save data or short press three times data can be saved.\u003c\/li\u003e\n\u003cli\u003eSET Press to enter the actual temperature and the operating mode query interface, digital (on) the actual measured temperature. Digital (lower) showing the operation mode. L represents the lower limit temperature below the set temperature, H is the upper limit temperature is higher than the temperature setting, OFF indicates when the temperature is between the upper and lower limits, the relay is in the off state.\u003c\/li\u003e\n\u003cli\u003eMode setting: Setting the temperature 1: temperature upper limit set temperature 2: lower limit temperature\u003c\/li\u003e\n\u003cli\u003eExample applications: now the upper limit temperature to 40.0 ℃, the minimum temperature is set to 20.0 ℃. At different temperature ranges relay operate as follows:\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature\u0026gt; 40 ℃, the relay 1 is closed, the relay 2 release;\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature of 20 ℃ ≤ ≤40 ℃ release relay 1, relay 2 release;\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature \u0026lt;20 ℃, the relay 2 is closed, the relay 1 release.\u003c\/li\u003e\n\u003cli\u003eParameter settings: the need for the user parameter settings must first hold the SET button and then give the thermostat power, to enter the parameter setting interface. There are three sets of parameters P0-P2 can be used for user settings.\u003c\/li\u003e\n\u003cli\u003eParameter setting item\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003eFunction Description Setting range Factory setting\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eP0 temperature correction -10 ℃ ~ + 10 ℃ 0\u003c\/li\u003e\n\u003cli\u003eP1 limit relay time 0 ~ 999s OFF\u003c\/li\u003e\n\u003cli\u003eP2 lower limit relay time 0 ~ 999s OFF\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003efriendly reminder:\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eP1 = OFF: indicates the actual temperature exceeds the upper limit temperature, corresponding relay will remain energized (long attracted state).\u003c\/li\u003e\n\u003cli\u003eP1 = 1 ~ 999: indicates the actual temperature exceeds the upper limit temperature, corresponding relay will energize long, then stop (Jog attracted state).\u003c\/li\u003e\n\u003cli\u003eP2 = OFF: indicates the actual temperature is below the lower limit temperature, corresponding relay will remain energized (long attracted state).\u003c\/li\u003e\n\u003cli\u003eP2 = 1 ~ 999: indicates the actual temperature is below the lower limit temperature, corresponding relay will energize long, then stop (Jog attracted state).\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003ePackage Inclued\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003e1PCS 12V Digital Dual Relay Alarm Thermometer Temperature Controller Air Regulator\u003c\/li\u003e\n\u003c\/ul\u003e"}
USB Charger Doctor Capacity Tester LCD Display Current Voltage Detector Meter

Translation missing: en.products.product.regular_price $7.99
{"id":4792266784839,"title":"12V Digital Thermometer Temperature Controller Dual Relay Alarm Air Regulator","handle":"12v-digital-thermometer-temperature-controller-dual-relay-alarm-air-regulator","description":"\u003cstrong\u003eDescription\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eTemperature range: -20 ℃ ~ + 100 ℃\u003c\/li\u003e\n\u003cli\u003eResolution: -9.9 ℃ ~ 99.9 ℃ paragraph 0.1 ℃, other temperature ranges 1 ℃\u003c\/li\u003e\n\u003cli\u003eTemperature measurement accuracy: 1 ℃\u003c\/li\u003e\n\u003cli\u003eMinimum temperature difference: 0.1 ℃\u003c\/li\u003e\n\u003cli\u003eRefresh rate about: 0.5S\u003c\/li\u003e\n\u003cli\u003eInput Power: DC 12V\u003c\/li\u003e\n\u003cli\u003eMeasuring input: 1 m NTC (10K 0.5%) alloy waterproof sensor\u003c\/li\u003e\n\u003cli\u003eOutput: Two relay 10A\u003c\/li\u003e\n\u003cli\u003eEnvironmental requirements: -10 ℃ ~ + 60 ℃ Humidity 20% to 75%\u003c\/li\u003e\n\u003cli\u003eSize: 70mm * 39mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003eIntelligent dual temperature control relay instructions\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eTips: Set the temperature when the buyer must ensure that the upper limit temperature is greater than the lower limit temperature, the system will work properly.\u003c\/li\u003e\n\u003cli\u003eCircuit connection: Connect the power supply with reference to the circuit diagram and load, the temperature sensor is missing or damaged digital tube will show \"- - -\", before using buyer must check the temperature sensor is installed.\u003c\/li\u003e\n\u003cli\u003eThe temperature output 10A relay, to meet a variety of high-power load, make sure that the line is correct.\u003c\/li\u003e\n\u003cli\u003eLEDs, LED status descriptions:\u003c\/li\u003e\n\u003cli\u003eLED: Off indicates the relay off, ON means the relay is closed\u003c\/li\u003e\n\u003cli\u003eDigital: Display \"- - -\", 1, check the temperature sensor 2 is missing or damaged, heating mode, high temperature protection 3, cryogenic cooling mode protection. In protected mode relay automatically disconnected.\u003c\/li\u003e\n\u003cli\u003eUse keys: temperature control panel has three buttons, button + button - SET button\u003c\/li\u003e\n\u003cli\u003eButton +: Achieving Rapid accumulation value\u003c\/li\u003e\n\u003cli\u003eKey: - fast diminishing value\u003c\/li\u003e\n\u003cli\u003eSET key SET: Temperature set temperature and operating mode interface query interface parameter setting interface\u003c\/li\u003e\n\u003cli\u003eDuring the SET press SET press according to different times, the corresponding digital temperature limit will be blinking, you can set the upper and lower temperature through the key addition and subtraction. After setting 8s automatically save data or short press three times data can be saved.\u003c\/li\u003e\n\u003cli\u003eSET Press to enter the actual temperature and the operating mode query interface, digital (on) the actual measured temperature. Digital (lower) showing the operation mode. L represents the lower limit temperature below the set temperature, H is the upper limit temperature is higher than the temperature setting, OFF indicates when the temperature is between the upper and lower limits, the relay is in the off state.\u003c\/li\u003e\n\u003cli\u003eMode setting: Setting the temperature 1: temperature upper limit set temperature 2: lower limit temperature\u003c\/li\u003e\n\u003cli\u003eExample applications: now the upper limit temperature to 40.0 ℃, the minimum temperature is set to 20.0 ℃. At different temperature ranges relay operate as follows:\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature\u0026gt; 40 ℃, the relay 1 is closed, the relay 2 release;\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature of 20 ℃ ≤ ≤40 ℃ release relay 1, relay 2 release;\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature \u0026lt;20 ℃, the relay 2 is closed, the relay 1 release.\u003c\/li\u003e\n\u003cli\u003eParameter settings: the need for the user parameter settings must first hold the SET button and then give the thermostat power, to enter the parameter setting interface. There are three sets of parameters P0-P2 can be used for user settings.\u003c\/li\u003e\n\u003cli\u003eParameter setting item\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003eFunction Description Setting range Factory setting\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eP0 temperature correction -10 ℃ ~ + 10 ℃ 0\u003c\/li\u003e\n\u003cli\u003eP1 limit relay time 0 ~ 999s OFF\u003c\/li\u003e\n\u003cli\u003eP2 lower limit relay time 0 ~ 999s OFF\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003efriendly reminder:\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eP1 = OFF: indicates the actual temperature exceeds the upper limit temperature, corresponding relay will remain energized (long attracted state).\u003c\/li\u003e\n\u003cli\u003eP1 = 1 ~ 999: indicates the actual temperature exceeds the upper limit temperature, corresponding relay will energize long, then stop (Jog attracted state).\u003c\/li\u003e\n\u003cli\u003eP2 = OFF: indicates the actual temperature is below the lower limit temperature, corresponding relay will remain energized (long attracted state).\u003c\/li\u003e\n\u003cli\u003eP2 = 1 ~ 999: indicates the actual temperature is below the lower limit temperature, corresponding relay will energize long, then stop (Jog attracted state).\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003ePackage Inclued\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003e1PCS 12V Digital Dual Relay Alarm Thermometer Temperature Controller Air Regulator\u003c\/li\u003e\n\u003c\/ul\u003e","published_at":"2020-08-14T11:39:05+08:00","created_at":"2020-08-14T11:39:03+08:00","vendor":"DIYMORE","type":"","tags":[],"price":999,"price_min":999,"price_max":999,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":32508226568263,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"011968","requires_shipping":true,"taxable":false,"featured_image":null,"available":true,"name":"12V Digital Thermometer Temperature Controller Dual Relay Alarm Air Regulator","public_title":null,"options":["Default Title"],"price":999,"weight":0,"compare_at_price":null,"inventory_management":"shopify","barcode":"","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/www.diymore.cc\/cdn\/shop\/products\/011968_1.jpg?v=1597376346","\/\/www.diymore.cc\/cdn\/shop\/products\/011968_3.jpg?v=1597376346","\/\/www.diymore.cc\/cdn\/shop\/products\/011968_2.jpg?v=1597376346","\/\/www.diymore.cc\/cdn\/shop\/products\/011968_4.jpg?v=1597376346","\/\/www.diymore.cc\/cdn\/shop\/products\/011968_6.jpg?v=1597376346","\/\/www.diymore.cc\/cdn\/shop\/products\/011968_5.jpg?v=1597376346"],"featured_image":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_1.jpg?v=1597376346","options":["Title"],"media":[{"alt":null,"id":7280857022535,"position":1,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_1.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_1.jpg?v=1597376346","width":1000},{"alt":null,"id":7280857055303,"position":2,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_3.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_3.jpg?v=1597376346","width":1000},{"alt":null,"id":7280857088071,"position":3,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_2.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_2.jpg?v=1597376346","width":1000},{"alt":null,"id":7280857120839,"position":4,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_4.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_4.jpg?v=1597376346","width":1000},{"alt":null,"id":7280857153607,"position":5,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_6.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_6.jpg?v=1597376346","width":1000},{"alt":null,"id":7280857186375,"position":6,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_5.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_5.jpg?v=1597376346","width":1000}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cstrong\u003eDescription\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eTemperature range: -20 ℃ ~ + 100 ℃\u003c\/li\u003e\n\u003cli\u003eResolution: -9.9 ℃ ~ 99.9 ℃ paragraph 0.1 ℃, other temperature ranges 1 ℃\u003c\/li\u003e\n\u003cli\u003eTemperature measurement accuracy: 1 ℃\u003c\/li\u003e\n\u003cli\u003eMinimum temperature difference: 0.1 ℃\u003c\/li\u003e\n\u003cli\u003eRefresh rate about: 0.5S\u003c\/li\u003e\n\u003cli\u003eInput Power: DC 12V\u003c\/li\u003e\n\u003cli\u003eMeasuring input: 1 m NTC (10K 0.5%) alloy waterproof sensor\u003c\/li\u003e\n\u003cli\u003eOutput: Two relay 10A\u003c\/li\u003e\n\u003cli\u003eEnvironmental requirements: -10 ℃ ~ + 60 ℃ Humidity 20% to 75%\u003c\/li\u003e\n\u003cli\u003eSize: 70mm * 39mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003eIntelligent dual temperature control relay instructions\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eTips: Set the temperature when the buyer must ensure that the upper limit temperature is greater than the lower limit temperature, the system will work properly.\u003c\/li\u003e\n\u003cli\u003eCircuit connection: Connect the power supply with reference to the circuit diagram and load, the temperature sensor is missing or damaged digital tube will show \"- - -\", before using buyer must check the temperature sensor is installed.\u003c\/li\u003e\n\u003cli\u003eThe temperature output 10A relay, to meet a variety of high-power load, make sure that the line is correct.\u003c\/li\u003e\n\u003cli\u003eLEDs, LED status descriptions:\u003c\/li\u003e\n\u003cli\u003eLED: Off indicates the relay off, ON means the relay is closed\u003c\/li\u003e\n\u003cli\u003eDigital: Display \"- - -\", 1, check the temperature sensor 2 is missing or damaged, heating mode, high temperature protection 3, cryogenic cooling mode protection. In protected mode relay automatically disconnected.\u003c\/li\u003e\n\u003cli\u003eUse keys: temperature control panel has three buttons, button + button - SET button\u003c\/li\u003e\n\u003cli\u003eButton +: Achieving Rapid accumulation value\u003c\/li\u003e\n\u003cli\u003eKey: - fast diminishing value\u003c\/li\u003e\n\u003cli\u003eSET key SET: Temperature set temperature and operating mode interface query interface parameter setting interface\u003c\/li\u003e\n\u003cli\u003eDuring the SET press SET press according to different times, the corresponding digital temperature limit will be blinking, you can set the upper and lower temperature through the key addition and subtraction. After setting 8s automatically save data or short press three times data can be saved.\u003c\/li\u003e\n\u003cli\u003eSET Press to enter the actual temperature and the operating mode query interface, digital (on) the actual measured temperature. Digital (lower) showing the operation mode. L represents the lower limit temperature below the set temperature, H is the upper limit temperature is higher than the temperature setting, OFF indicates when the temperature is between the upper and lower limits, the relay is in the off state.\u003c\/li\u003e\n\u003cli\u003eMode setting: Setting the temperature 1: temperature upper limit set temperature 2: lower limit temperature\u003c\/li\u003e\n\u003cli\u003eExample applications: now the upper limit temperature to 40.0 ℃, the minimum temperature is set to 20.0 ℃. At different temperature ranges relay operate as follows:\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature\u0026gt; 40 ℃, the relay 1 is closed, the relay 2 release;\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature of 20 ℃ ≤ ≤40 ℃ release relay 1, relay 2 release;\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature \u0026lt;20 ℃, the relay 2 is closed, the relay 1 release.\u003c\/li\u003e\n\u003cli\u003eParameter settings: the need for the user parameter settings must first hold the SET button and then give the thermostat power, to enter the parameter setting interface. There are three sets of parameters P0-P2 can be used for user settings.\u003c\/li\u003e\n\u003cli\u003eParameter setting item\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003eFunction Description Setting range Factory setting\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eP0 temperature correction -10 ℃ ~ + 10 ℃ 0\u003c\/li\u003e\n\u003cli\u003eP1 limit relay time 0 ~ 999s OFF\u003c\/li\u003e\n\u003cli\u003eP2 lower limit relay time 0 ~ 999s OFF\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003efriendly reminder:\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eP1 = OFF: indicates the actual temperature exceeds the upper limit temperature, corresponding relay will remain energized (long attracted state).\u003c\/li\u003e\n\u003cli\u003eP1 = 1 ~ 999: indicates the actual temperature exceeds the upper limit temperature, corresponding relay will energize long, then stop (Jog attracted state).\u003c\/li\u003e\n\u003cli\u003eP2 = OFF: indicates the actual temperature is below the lower limit temperature, corresponding relay will remain energized (long attracted state).\u003c\/li\u003e\n\u003cli\u003eP2 = 1 ~ 999: indicates the actual temperature is below the lower limit temperature, corresponding relay will energize long, then stop (Jog attracted state).\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003ePackage Inclued\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003e1PCS 12V Digital Dual Relay Alarm Thermometer Temperature Controller Air Regulator\u003c\/li\u003e\n\u003c\/ul\u003e"}
ESP32 ESP8266 4x 18650 Battery USB Power Bank Shield Holder V9 3V/5V

Translation missing: en.products.product.regular_price $9.99
{"id":4792266784839,"title":"12V Digital Thermometer Temperature Controller Dual Relay Alarm Air Regulator","handle":"12v-digital-thermometer-temperature-controller-dual-relay-alarm-air-regulator","description":"\u003cstrong\u003eDescription\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eTemperature range: -20 ℃ ~ + 100 ℃\u003c\/li\u003e\n\u003cli\u003eResolution: -9.9 ℃ ~ 99.9 ℃ paragraph 0.1 ℃, other temperature ranges 1 ℃\u003c\/li\u003e\n\u003cli\u003eTemperature measurement accuracy: 1 ℃\u003c\/li\u003e\n\u003cli\u003eMinimum temperature difference: 0.1 ℃\u003c\/li\u003e\n\u003cli\u003eRefresh rate about: 0.5S\u003c\/li\u003e\n\u003cli\u003eInput Power: DC 12V\u003c\/li\u003e\n\u003cli\u003eMeasuring input: 1 m NTC (10K 0.5%) alloy waterproof sensor\u003c\/li\u003e\n\u003cli\u003eOutput: Two relay 10A\u003c\/li\u003e\n\u003cli\u003eEnvironmental requirements: -10 ℃ ~ + 60 ℃ Humidity 20% to 75%\u003c\/li\u003e\n\u003cli\u003eSize: 70mm * 39mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003eIntelligent dual temperature control relay instructions\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eTips: Set the temperature when the buyer must ensure that the upper limit temperature is greater than the lower limit temperature, the system will work properly.\u003c\/li\u003e\n\u003cli\u003eCircuit connection: Connect the power supply with reference to the circuit diagram and load, the temperature sensor is missing or damaged digital tube will show \"- - -\", before using buyer must check the temperature sensor is installed.\u003c\/li\u003e\n\u003cli\u003eThe temperature output 10A relay, to meet a variety of high-power load, make sure that the line is correct.\u003c\/li\u003e\n\u003cli\u003eLEDs, LED status descriptions:\u003c\/li\u003e\n\u003cli\u003eLED: Off indicates the relay off, ON means the relay is closed\u003c\/li\u003e\n\u003cli\u003eDigital: Display \"- - -\", 1, check the temperature sensor 2 is missing or damaged, heating mode, high temperature protection 3, cryogenic cooling mode protection. In protected mode relay automatically disconnected.\u003c\/li\u003e\n\u003cli\u003eUse keys: temperature control panel has three buttons, button + button - SET button\u003c\/li\u003e\n\u003cli\u003eButton +: Achieving Rapid accumulation value\u003c\/li\u003e\n\u003cli\u003eKey: - fast diminishing value\u003c\/li\u003e\n\u003cli\u003eSET key SET: Temperature set temperature and operating mode interface query interface parameter setting interface\u003c\/li\u003e\n\u003cli\u003eDuring the SET press SET press according to different times, the corresponding digital temperature limit will be blinking, you can set the upper and lower temperature through the key addition and subtraction. After setting 8s automatically save data or short press three times data can be saved.\u003c\/li\u003e\n\u003cli\u003eSET Press to enter the actual temperature and the operating mode query interface, digital (on) the actual measured temperature. Digital (lower) showing the operation mode. L represents the lower limit temperature below the set temperature, H is the upper limit temperature is higher than the temperature setting, OFF indicates when the temperature is between the upper and lower limits, the relay is in the off state.\u003c\/li\u003e\n\u003cli\u003eMode setting: Setting the temperature 1: temperature upper limit set temperature 2: lower limit temperature\u003c\/li\u003e\n\u003cli\u003eExample applications: now the upper limit temperature to 40.0 ℃, the minimum temperature is set to 20.0 ℃. At different temperature ranges relay operate as follows:\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature\u0026gt; 40 ℃, the relay 1 is closed, the relay 2 release;\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature of 20 ℃ ≤ ≤40 ℃ release relay 1, relay 2 release;\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature \u0026lt;20 ℃, the relay 2 is closed, the relay 1 release.\u003c\/li\u003e\n\u003cli\u003eParameter settings: the need for the user parameter settings must first hold the SET button and then give the thermostat power, to enter the parameter setting interface. There are three sets of parameters P0-P2 can be used for user settings.\u003c\/li\u003e\n\u003cli\u003eParameter setting item\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003eFunction Description Setting range Factory setting\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eP0 temperature correction -10 ℃ ~ + 10 ℃ 0\u003c\/li\u003e\n\u003cli\u003eP1 limit relay time 0 ~ 999s OFF\u003c\/li\u003e\n\u003cli\u003eP2 lower limit relay time 0 ~ 999s OFF\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003efriendly reminder:\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eP1 = OFF: indicates the actual temperature exceeds the upper limit temperature, corresponding relay will remain energized (long attracted state).\u003c\/li\u003e\n\u003cli\u003eP1 = 1 ~ 999: indicates the actual temperature exceeds the upper limit temperature, corresponding relay will energize long, then stop (Jog attracted state).\u003c\/li\u003e\n\u003cli\u003eP2 = OFF: indicates the actual temperature is below the lower limit temperature, corresponding relay will remain energized (long attracted state).\u003c\/li\u003e\n\u003cli\u003eP2 = 1 ~ 999: indicates the actual temperature is below the lower limit temperature, corresponding relay will energize long, then stop (Jog attracted state).\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003ePackage Inclued\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003e1PCS 12V Digital Dual Relay Alarm Thermometer Temperature Controller Air Regulator\u003c\/li\u003e\n\u003c\/ul\u003e","published_at":"2020-08-14T11:39:05+08:00","created_at":"2020-08-14T11:39:03+08:00","vendor":"DIYMORE","type":"","tags":[],"price":999,"price_min":999,"price_max":999,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":32508226568263,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"011968","requires_shipping":true,"taxable":false,"featured_image":null,"available":true,"name":"12V Digital Thermometer Temperature Controller Dual Relay Alarm Air Regulator","public_title":null,"options":["Default Title"],"price":999,"weight":0,"compare_at_price":null,"inventory_management":"shopify","barcode":"","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/www.diymore.cc\/cdn\/shop\/products\/011968_1.jpg?v=1597376346","\/\/www.diymore.cc\/cdn\/shop\/products\/011968_3.jpg?v=1597376346","\/\/www.diymore.cc\/cdn\/shop\/products\/011968_2.jpg?v=1597376346","\/\/www.diymore.cc\/cdn\/shop\/products\/011968_4.jpg?v=1597376346","\/\/www.diymore.cc\/cdn\/shop\/products\/011968_6.jpg?v=1597376346","\/\/www.diymore.cc\/cdn\/shop\/products\/011968_5.jpg?v=1597376346"],"featured_image":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_1.jpg?v=1597376346","options":["Title"],"media":[{"alt":null,"id":7280857022535,"position":1,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_1.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_1.jpg?v=1597376346","width":1000},{"alt":null,"id":7280857055303,"position":2,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_3.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_3.jpg?v=1597376346","width":1000},{"alt":null,"id":7280857088071,"position":3,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_2.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_2.jpg?v=1597376346","width":1000},{"alt":null,"id":7280857120839,"position":4,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_4.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_4.jpg?v=1597376346","width":1000},{"alt":null,"id":7280857153607,"position":5,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_6.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_6.jpg?v=1597376346","width":1000},{"alt":null,"id":7280857186375,"position":6,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_5.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_5.jpg?v=1597376346","width":1000}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cstrong\u003eDescription\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eTemperature range: -20 ℃ ~ + 100 ℃\u003c\/li\u003e\n\u003cli\u003eResolution: -9.9 ℃ ~ 99.9 ℃ paragraph 0.1 ℃, other temperature ranges 1 ℃\u003c\/li\u003e\n\u003cli\u003eTemperature measurement accuracy: 1 ℃\u003c\/li\u003e\n\u003cli\u003eMinimum temperature difference: 0.1 ℃\u003c\/li\u003e\n\u003cli\u003eRefresh rate about: 0.5S\u003c\/li\u003e\n\u003cli\u003eInput Power: DC 12V\u003c\/li\u003e\n\u003cli\u003eMeasuring input: 1 m NTC (10K 0.5%) alloy waterproof sensor\u003c\/li\u003e\n\u003cli\u003eOutput: Two relay 10A\u003c\/li\u003e\n\u003cli\u003eEnvironmental requirements: -10 ℃ ~ + 60 ℃ Humidity 20% to 75%\u003c\/li\u003e\n\u003cli\u003eSize: 70mm * 39mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003eIntelligent dual temperature control relay instructions\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eTips: Set the temperature when the buyer must ensure that the upper limit temperature is greater than the lower limit temperature, the system will work properly.\u003c\/li\u003e\n\u003cli\u003eCircuit connection: Connect the power supply with reference to the circuit diagram and load, the temperature sensor is missing or damaged digital tube will show \"- - -\", before using buyer must check the temperature sensor is installed.\u003c\/li\u003e\n\u003cli\u003eThe temperature output 10A relay, to meet a variety of high-power load, make sure that the line is correct.\u003c\/li\u003e\n\u003cli\u003eLEDs, LED status descriptions:\u003c\/li\u003e\n\u003cli\u003eLED: Off indicates the relay off, ON means the relay is closed\u003c\/li\u003e\n\u003cli\u003eDigital: Display \"- - -\", 1, check the temperature sensor 2 is missing or damaged, heating mode, high temperature protection 3, cryogenic cooling mode protection. In protected mode relay automatically disconnected.\u003c\/li\u003e\n\u003cli\u003eUse keys: temperature control panel has three buttons, button + button - SET button\u003c\/li\u003e\n\u003cli\u003eButton +: Achieving Rapid accumulation value\u003c\/li\u003e\n\u003cli\u003eKey: - fast diminishing value\u003c\/li\u003e\n\u003cli\u003eSET key SET: Temperature set temperature and operating mode interface query interface parameter setting interface\u003c\/li\u003e\n\u003cli\u003eDuring the SET press SET press according to different times, the corresponding digital temperature limit will be blinking, you can set the upper and lower temperature through the key addition and subtraction. After setting 8s automatically save data or short press three times data can be saved.\u003c\/li\u003e\n\u003cli\u003eSET Press to enter the actual temperature and the operating mode query interface, digital (on) the actual measured temperature. Digital (lower) showing the operation mode. L represents the lower limit temperature below the set temperature, H is the upper limit temperature is higher than the temperature setting, OFF indicates when the temperature is between the upper and lower limits, the relay is in the off state.\u003c\/li\u003e\n\u003cli\u003eMode setting: Setting the temperature 1: temperature upper limit set temperature 2: lower limit temperature\u003c\/li\u003e\n\u003cli\u003eExample applications: now the upper limit temperature to 40.0 ℃, the minimum temperature is set to 20.0 ℃. At different temperature ranges relay operate as follows:\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature\u0026gt; 40 ℃, the relay 1 is closed, the relay 2 release;\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature of 20 ℃ ≤ ≤40 ℃ release relay 1, relay 2 release;\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature \u0026lt;20 ℃, the relay 2 is closed, the relay 1 release.\u003c\/li\u003e\n\u003cli\u003eParameter settings: the need for the user parameter settings must first hold the SET button and then give the thermostat power, to enter the parameter setting interface. There are three sets of parameters P0-P2 can be used for user settings.\u003c\/li\u003e\n\u003cli\u003eParameter setting item\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003eFunction Description Setting range Factory setting\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eP0 temperature correction -10 ℃ ~ + 10 ℃ 0\u003c\/li\u003e\n\u003cli\u003eP1 limit relay time 0 ~ 999s OFF\u003c\/li\u003e\n\u003cli\u003eP2 lower limit relay time 0 ~ 999s OFF\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003efriendly reminder:\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eP1 = OFF: indicates the actual temperature exceeds the upper limit temperature, corresponding relay will remain energized (long attracted state).\u003c\/li\u003e\n\u003cli\u003eP1 = 1 ~ 999: indicates the actual temperature exceeds the upper limit temperature, corresponding relay will energize long, then stop (Jog attracted state).\u003c\/li\u003e\n\u003cli\u003eP2 = OFF: indicates the actual temperature is below the lower limit temperature, corresponding relay will remain energized (long attracted state).\u003c\/li\u003e\n\u003cli\u003eP2 = 1 ~ 999: indicates the actual temperature is below the lower limit temperature, corresponding relay will energize long, then stop (Jog attracted state).\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003ePackage Inclued\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003e1PCS 12V Digital Dual Relay Alarm Thermometer Temperature Controller Air Regulator\u003c\/li\u003e\n\u003c\/ul\u003e"}
10cm 40pin Male to Male/ M-F/F-F Wire Jumper Breadboard Multicolored Dupont Ribbon Cables Kit for Arduino

Translation missing: en.products.product.regular_price $5.99
{"id":4792266784839,"title":"12V Digital Thermometer Temperature Controller Dual Relay Alarm Air Regulator","handle":"12v-digital-thermometer-temperature-controller-dual-relay-alarm-air-regulator","description":"\u003cstrong\u003eDescription\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eTemperature range: -20 ℃ ~ + 100 ℃\u003c\/li\u003e\n\u003cli\u003eResolution: -9.9 ℃ ~ 99.9 ℃ paragraph 0.1 ℃, other temperature ranges 1 ℃\u003c\/li\u003e\n\u003cli\u003eTemperature measurement accuracy: 1 ℃\u003c\/li\u003e\n\u003cli\u003eMinimum temperature difference: 0.1 ℃\u003c\/li\u003e\n\u003cli\u003eRefresh rate about: 0.5S\u003c\/li\u003e\n\u003cli\u003eInput Power: DC 12V\u003c\/li\u003e\n\u003cli\u003eMeasuring input: 1 m NTC (10K 0.5%) alloy waterproof sensor\u003c\/li\u003e\n\u003cli\u003eOutput: Two relay 10A\u003c\/li\u003e\n\u003cli\u003eEnvironmental requirements: -10 ℃ ~ + 60 ℃ Humidity 20% to 75%\u003c\/li\u003e\n\u003cli\u003eSize: 70mm * 39mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003eIntelligent dual temperature control relay instructions\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eTips: Set the temperature when the buyer must ensure that the upper limit temperature is greater than the lower limit temperature, the system will work properly.\u003c\/li\u003e\n\u003cli\u003eCircuit connection: Connect the power supply with reference to the circuit diagram and load, the temperature sensor is missing or damaged digital tube will show \"- - -\", before using buyer must check the temperature sensor is installed.\u003c\/li\u003e\n\u003cli\u003eThe temperature output 10A relay, to meet a variety of high-power load, make sure that the line is correct.\u003c\/li\u003e\n\u003cli\u003eLEDs, LED status descriptions:\u003c\/li\u003e\n\u003cli\u003eLED: Off indicates the relay off, ON means the relay is closed\u003c\/li\u003e\n\u003cli\u003eDigital: Display \"- - -\", 1, check the temperature sensor 2 is missing or damaged, heating mode, high temperature protection 3, cryogenic cooling mode protection. In protected mode relay automatically disconnected.\u003c\/li\u003e\n\u003cli\u003eUse keys: temperature control panel has three buttons, button + button - SET button\u003c\/li\u003e\n\u003cli\u003eButton +: Achieving Rapid accumulation value\u003c\/li\u003e\n\u003cli\u003eKey: - fast diminishing value\u003c\/li\u003e\n\u003cli\u003eSET key SET: Temperature set temperature and operating mode interface query interface parameter setting interface\u003c\/li\u003e\n\u003cli\u003eDuring the SET press SET press according to different times, the corresponding digital temperature limit will be blinking, you can set the upper and lower temperature through the key addition and subtraction. After setting 8s automatically save data or short press three times data can be saved.\u003c\/li\u003e\n\u003cli\u003eSET Press to enter the actual temperature and the operating mode query interface, digital (on) the actual measured temperature. Digital (lower) showing the operation mode. L represents the lower limit temperature below the set temperature, H is the upper limit temperature is higher than the temperature setting, OFF indicates when the temperature is between the upper and lower limits, the relay is in the off state.\u003c\/li\u003e\n\u003cli\u003eMode setting: Setting the temperature 1: temperature upper limit set temperature 2: lower limit temperature\u003c\/li\u003e\n\u003cli\u003eExample applications: now the upper limit temperature to 40.0 ℃, the minimum temperature is set to 20.0 ℃. At different temperature ranges relay operate as follows:\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature\u0026gt; 40 ℃, the relay 1 is closed, the relay 2 release;\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature of 20 ℃ ≤ ≤40 ℃ release relay 1, relay 2 release;\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature \u0026lt;20 ℃, the relay 2 is closed, the relay 1 release.\u003c\/li\u003e\n\u003cli\u003eParameter settings: the need for the user parameter settings must first hold the SET button and then give the thermostat power, to enter the parameter setting interface. There are three sets of parameters P0-P2 can be used for user settings.\u003c\/li\u003e\n\u003cli\u003eParameter setting item\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003eFunction Description Setting range Factory setting\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eP0 temperature correction -10 ℃ ~ + 10 ℃ 0\u003c\/li\u003e\n\u003cli\u003eP1 limit relay time 0 ~ 999s OFF\u003c\/li\u003e\n\u003cli\u003eP2 lower limit relay time 0 ~ 999s OFF\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003efriendly reminder:\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eP1 = OFF: indicates the actual temperature exceeds the upper limit temperature, corresponding relay will remain energized (long attracted state).\u003c\/li\u003e\n\u003cli\u003eP1 = 1 ~ 999: indicates the actual temperature exceeds the upper limit temperature, corresponding relay will energize long, then stop (Jog attracted state).\u003c\/li\u003e\n\u003cli\u003eP2 = OFF: indicates the actual temperature is below the lower limit temperature, corresponding relay will remain energized (long attracted state).\u003c\/li\u003e\n\u003cli\u003eP2 = 1 ~ 999: indicates the actual temperature is below the lower limit temperature, corresponding relay will energize long, then stop (Jog attracted state).\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003ePackage Inclued\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003e1PCS 12V Digital Dual Relay Alarm Thermometer Temperature Controller Air Regulator\u003c\/li\u003e\n\u003c\/ul\u003e","published_at":"2020-08-14T11:39:05+08:00","created_at":"2020-08-14T11:39:03+08:00","vendor":"DIYMORE","type":"","tags":[],"price":999,"price_min":999,"price_max":999,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":32508226568263,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"011968","requires_shipping":true,"taxable":false,"featured_image":null,"available":true,"name":"12V Digital Thermometer Temperature Controller Dual Relay Alarm Air Regulator","public_title":null,"options":["Default Title"],"price":999,"weight":0,"compare_at_price":null,"inventory_management":"shopify","barcode":"","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/www.diymore.cc\/cdn\/shop\/products\/011968_1.jpg?v=1597376346","\/\/www.diymore.cc\/cdn\/shop\/products\/011968_3.jpg?v=1597376346","\/\/www.diymore.cc\/cdn\/shop\/products\/011968_2.jpg?v=1597376346","\/\/www.diymore.cc\/cdn\/shop\/products\/011968_4.jpg?v=1597376346","\/\/www.diymore.cc\/cdn\/shop\/products\/011968_6.jpg?v=1597376346","\/\/www.diymore.cc\/cdn\/shop\/products\/011968_5.jpg?v=1597376346"],"featured_image":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_1.jpg?v=1597376346","options":["Title"],"media":[{"alt":null,"id":7280857022535,"position":1,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_1.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_1.jpg?v=1597376346","width":1000},{"alt":null,"id":7280857055303,"position":2,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_3.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_3.jpg?v=1597376346","width":1000},{"alt":null,"id":7280857088071,"position":3,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_2.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_2.jpg?v=1597376346","width":1000},{"alt":null,"id":7280857120839,"position":4,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_4.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_4.jpg?v=1597376346","width":1000},{"alt":null,"id":7280857153607,"position":5,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_6.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_6.jpg?v=1597376346","width":1000},{"alt":null,"id":7280857186375,"position":6,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_5.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_5.jpg?v=1597376346","width":1000}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cstrong\u003eDescription\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eTemperature range: -20 ℃ ~ + 100 ℃\u003c\/li\u003e\n\u003cli\u003eResolution: -9.9 ℃ ~ 99.9 ℃ paragraph 0.1 ℃, other temperature ranges 1 ℃\u003c\/li\u003e\n\u003cli\u003eTemperature measurement accuracy: 1 ℃\u003c\/li\u003e\n\u003cli\u003eMinimum temperature difference: 0.1 ℃\u003c\/li\u003e\n\u003cli\u003eRefresh rate about: 0.5S\u003c\/li\u003e\n\u003cli\u003eInput Power: DC 12V\u003c\/li\u003e\n\u003cli\u003eMeasuring input: 1 m NTC (10K 0.5%) alloy waterproof sensor\u003c\/li\u003e\n\u003cli\u003eOutput: Two relay 10A\u003c\/li\u003e\n\u003cli\u003eEnvironmental requirements: -10 ℃ ~ + 60 ℃ Humidity 20% to 75%\u003c\/li\u003e\n\u003cli\u003eSize: 70mm * 39mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003eIntelligent dual temperature control relay instructions\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eTips: Set the temperature when the buyer must ensure that the upper limit temperature is greater than the lower limit temperature, the system will work properly.\u003c\/li\u003e\n\u003cli\u003eCircuit connection: Connect the power supply with reference to the circuit diagram and load, the temperature sensor is missing or damaged digital tube will show \"- - -\", before using buyer must check the temperature sensor is installed.\u003c\/li\u003e\n\u003cli\u003eThe temperature output 10A relay, to meet a variety of high-power load, make sure that the line is correct.\u003c\/li\u003e\n\u003cli\u003eLEDs, LED status descriptions:\u003c\/li\u003e\n\u003cli\u003eLED: Off indicates the relay off, ON means the relay is closed\u003c\/li\u003e\n\u003cli\u003eDigital: Display \"- - -\", 1, check the temperature sensor 2 is missing or damaged, heating mode, high temperature protection 3, cryogenic cooling mode protection. In protected mode relay automatically disconnected.\u003c\/li\u003e\n\u003cli\u003eUse keys: temperature control panel has three buttons, button + button - SET button\u003c\/li\u003e\n\u003cli\u003eButton +: Achieving Rapid accumulation value\u003c\/li\u003e\n\u003cli\u003eKey: - fast diminishing value\u003c\/li\u003e\n\u003cli\u003eSET key SET: Temperature set temperature and operating mode interface query interface parameter setting interface\u003c\/li\u003e\n\u003cli\u003eDuring the SET press SET press according to different times, the corresponding digital temperature limit will be blinking, you can set the upper and lower temperature through the key addition and subtraction. After setting 8s automatically save data or short press three times data can be saved.\u003c\/li\u003e\n\u003cli\u003eSET Press to enter the actual temperature and the operating mode query interface, digital (on) the actual measured temperature. Digital (lower) showing the operation mode. L represents the lower limit temperature below the set temperature, H is the upper limit temperature is higher than the temperature setting, OFF indicates when the temperature is between the upper and lower limits, the relay is in the off state.\u003c\/li\u003e\n\u003cli\u003eMode setting: Setting the temperature 1: temperature upper limit set temperature 2: lower limit temperature\u003c\/li\u003e\n\u003cli\u003eExample applications: now the upper limit temperature to 40.0 ℃, the minimum temperature is set to 20.0 ℃. At different temperature ranges relay operate as follows:\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature\u0026gt; 40 ℃, the relay 1 is closed, the relay 2 release;\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature of 20 ℃ ≤ ≤40 ℃ release relay 1, relay 2 release;\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature \u0026lt;20 ℃, the relay 2 is closed, the relay 1 release.\u003c\/li\u003e\n\u003cli\u003eParameter settings: the need for the user parameter settings must first hold the SET button and then give the thermostat power, to enter the parameter setting interface. There are three sets of parameters P0-P2 can be used for user settings.\u003c\/li\u003e\n\u003cli\u003eParameter setting item\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003eFunction Description Setting range Factory setting\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eP0 temperature correction -10 ℃ ~ + 10 ℃ 0\u003c\/li\u003e\n\u003cli\u003eP1 limit relay time 0 ~ 999s OFF\u003c\/li\u003e\n\u003cli\u003eP2 lower limit relay time 0 ~ 999s OFF\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003efriendly reminder:\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eP1 = OFF: indicates the actual temperature exceeds the upper limit temperature, corresponding relay will remain energized (long attracted state).\u003c\/li\u003e\n\u003cli\u003eP1 = 1 ~ 999: indicates the actual temperature exceeds the upper limit temperature, corresponding relay will energize long, then stop (Jog attracted state).\u003c\/li\u003e\n\u003cli\u003eP2 = OFF: indicates the actual temperature is below the lower limit temperature, corresponding relay will remain energized (long attracted state).\u003c\/li\u003e\n\u003cli\u003eP2 = 1 ~ 999: indicates the actual temperature is below the lower limit temperature, corresponding relay will energize long, then stop (Jog attracted state).\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003ePackage Inclued\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003e1PCS 12V Digital Dual Relay Alarm Thermometer Temperature Controller Air Regulator\u003c\/li\u003e\n\u003c\/ul\u003e"}
DC 5V 12V Jog Self lock Smart WiFi Wireless Switch Thet Relay Module APP Control Control Diy Electronic PCB Board

Translation missing: en.products.product.regular_price $8.99
{"id":4792266784839,"title":"12V Digital Thermometer Temperature Controller Dual Relay Alarm Air Regulator","handle":"12v-digital-thermometer-temperature-controller-dual-relay-alarm-air-regulator","description":"\u003cstrong\u003eDescription\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eTemperature range: -20 ℃ ~ + 100 ℃\u003c\/li\u003e\n\u003cli\u003eResolution: -9.9 ℃ ~ 99.9 ℃ paragraph 0.1 ℃, other temperature ranges 1 ℃\u003c\/li\u003e\n\u003cli\u003eTemperature measurement accuracy: 1 ℃\u003c\/li\u003e\n\u003cli\u003eMinimum temperature difference: 0.1 ℃\u003c\/li\u003e\n\u003cli\u003eRefresh rate about: 0.5S\u003c\/li\u003e\n\u003cli\u003eInput Power: DC 12V\u003c\/li\u003e\n\u003cli\u003eMeasuring input: 1 m NTC (10K 0.5%) alloy waterproof sensor\u003c\/li\u003e\n\u003cli\u003eOutput: Two relay 10A\u003c\/li\u003e\n\u003cli\u003eEnvironmental requirements: -10 ℃ ~ + 60 ℃ Humidity 20% to 75%\u003c\/li\u003e\n\u003cli\u003eSize: 70mm * 39mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003eIntelligent dual temperature control relay instructions\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eTips: Set the temperature when the buyer must ensure that the upper limit temperature is greater than the lower limit temperature, the system will work properly.\u003c\/li\u003e\n\u003cli\u003eCircuit connection: Connect the power supply with reference to the circuit diagram and load, the temperature sensor is missing or damaged digital tube will show \"- - -\", before using buyer must check the temperature sensor is installed.\u003c\/li\u003e\n\u003cli\u003eThe temperature output 10A relay, to meet a variety of high-power load, make sure that the line is correct.\u003c\/li\u003e\n\u003cli\u003eLEDs, LED status descriptions:\u003c\/li\u003e\n\u003cli\u003eLED: Off indicates the relay off, ON means the relay is closed\u003c\/li\u003e\n\u003cli\u003eDigital: Display \"- - -\", 1, check the temperature sensor 2 is missing or damaged, heating mode, high temperature protection 3, cryogenic cooling mode protection. In protected mode relay automatically disconnected.\u003c\/li\u003e\n\u003cli\u003eUse keys: temperature control panel has three buttons, button + button - SET button\u003c\/li\u003e\n\u003cli\u003eButton +: Achieving Rapid accumulation value\u003c\/li\u003e\n\u003cli\u003eKey: - fast diminishing value\u003c\/li\u003e\n\u003cli\u003eSET key SET: Temperature set temperature and operating mode interface query interface parameter setting interface\u003c\/li\u003e\n\u003cli\u003eDuring the SET press SET press according to different times, the corresponding digital temperature limit will be blinking, you can set the upper and lower temperature through the key addition and subtraction. After setting 8s automatically save data or short press three times data can be saved.\u003c\/li\u003e\n\u003cli\u003eSET Press to enter the actual temperature and the operating mode query interface, digital (on) the actual measured temperature. Digital (lower) showing the operation mode. L represents the lower limit temperature below the set temperature, H is the upper limit temperature is higher than the temperature setting, OFF indicates when the temperature is between the upper and lower limits, the relay is in the off state.\u003c\/li\u003e\n\u003cli\u003eMode setting: Setting the temperature 1: temperature upper limit set temperature 2: lower limit temperature\u003c\/li\u003e\n\u003cli\u003eExample applications: now the upper limit temperature to 40.0 ℃, the minimum temperature is set to 20.0 ℃. At different temperature ranges relay operate as follows:\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature\u0026gt; 40 ℃, the relay 1 is closed, the relay 2 release;\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature of 20 ℃ ≤ ≤40 ℃ release relay 1, relay 2 release;\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature \u0026lt;20 ℃, the relay 2 is closed, the relay 1 release.\u003c\/li\u003e\n\u003cli\u003eParameter settings: the need for the user parameter settings must first hold the SET button and then give the thermostat power, to enter the parameter setting interface. There are three sets of parameters P0-P2 can be used for user settings.\u003c\/li\u003e\n\u003cli\u003eParameter setting item\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003eFunction Description Setting range Factory setting\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eP0 temperature correction -10 ℃ ~ + 10 ℃ 0\u003c\/li\u003e\n\u003cli\u003eP1 limit relay time 0 ~ 999s OFF\u003c\/li\u003e\n\u003cli\u003eP2 lower limit relay time 0 ~ 999s OFF\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003efriendly reminder:\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eP1 = OFF: indicates the actual temperature exceeds the upper limit temperature, corresponding relay will remain energized (long attracted state).\u003c\/li\u003e\n\u003cli\u003eP1 = 1 ~ 999: indicates the actual temperature exceeds the upper limit temperature, corresponding relay will energize long, then stop (Jog attracted state).\u003c\/li\u003e\n\u003cli\u003eP2 = OFF: indicates the actual temperature is below the lower limit temperature, corresponding relay will remain energized (long attracted state).\u003c\/li\u003e\n\u003cli\u003eP2 = 1 ~ 999: indicates the actual temperature is below the lower limit temperature, corresponding relay will energize long, then stop (Jog attracted state).\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003ePackage Inclued\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003e1PCS 12V Digital Dual Relay Alarm Thermometer Temperature Controller Air Regulator\u003c\/li\u003e\n\u003c\/ul\u003e","published_at":"2020-08-14T11:39:05+08:00","created_at":"2020-08-14T11:39:03+08:00","vendor":"DIYMORE","type":"","tags":[],"price":999,"price_min":999,"price_max":999,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":32508226568263,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"011968","requires_shipping":true,"taxable":false,"featured_image":null,"available":true,"name":"12V Digital Thermometer Temperature Controller Dual Relay Alarm Air Regulator","public_title":null,"options":["Default Title"],"price":999,"weight":0,"compare_at_price":null,"inventory_management":"shopify","barcode":"","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/www.diymore.cc\/cdn\/shop\/products\/011968_1.jpg?v=1597376346","\/\/www.diymore.cc\/cdn\/shop\/products\/011968_3.jpg?v=1597376346","\/\/www.diymore.cc\/cdn\/shop\/products\/011968_2.jpg?v=1597376346","\/\/www.diymore.cc\/cdn\/shop\/products\/011968_4.jpg?v=1597376346","\/\/www.diymore.cc\/cdn\/shop\/products\/011968_6.jpg?v=1597376346","\/\/www.diymore.cc\/cdn\/shop\/products\/011968_5.jpg?v=1597376346"],"featured_image":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_1.jpg?v=1597376346","options":["Title"],"media":[{"alt":null,"id":7280857022535,"position":1,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_1.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_1.jpg?v=1597376346","width":1000},{"alt":null,"id":7280857055303,"position":2,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_3.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_3.jpg?v=1597376346","width":1000},{"alt":null,"id":7280857088071,"position":3,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_2.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_2.jpg?v=1597376346","width":1000},{"alt":null,"id":7280857120839,"position":4,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_4.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_4.jpg?v=1597376346","width":1000},{"alt":null,"id":7280857153607,"position":5,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_6.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_6.jpg?v=1597376346","width":1000},{"alt":null,"id":7280857186375,"position":6,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_5.jpg?v=1597376346"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/011968_5.jpg?v=1597376346","width":1000}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cstrong\u003eDescription\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eTemperature range: -20 ℃ ~ + 100 ℃\u003c\/li\u003e\n\u003cli\u003eResolution: -9.9 ℃ ~ 99.9 ℃ paragraph 0.1 ℃, other temperature ranges 1 ℃\u003c\/li\u003e\n\u003cli\u003eTemperature measurement accuracy: 1 ℃\u003c\/li\u003e\n\u003cli\u003eMinimum temperature difference: 0.1 ℃\u003c\/li\u003e\n\u003cli\u003eRefresh rate about: 0.5S\u003c\/li\u003e\n\u003cli\u003eInput Power: DC 12V\u003c\/li\u003e\n\u003cli\u003eMeasuring input: 1 m NTC (10K 0.5%) alloy waterproof sensor\u003c\/li\u003e\n\u003cli\u003eOutput: Two relay 10A\u003c\/li\u003e\n\u003cli\u003eEnvironmental requirements: -10 ℃ ~ + 60 ℃ Humidity 20% to 75%\u003c\/li\u003e\n\u003cli\u003eSize: 70mm * 39mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003eIntelligent dual temperature control relay instructions\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eTips: Set the temperature when the buyer must ensure that the upper limit temperature is greater than the lower limit temperature, the system will work properly.\u003c\/li\u003e\n\u003cli\u003eCircuit connection: Connect the power supply with reference to the circuit diagram and load, the temperature sensor is missing or damaged digital tube will show \"- - -\", before using buyer must check the temperature sensor is installed.\u003c\/li\u003e\n\u003cli\u003eThe temperature output 10A relay, to meet a variety of high-power load, make sure that the line is correct.\u003c\/li\u003e\n\u003cli\u003eLEDs, LED status descriptions:\u003c\/li\u003e\n\u003cli\u003eLED: Off indicates the relay off, ON means the relay is closed\u003c\/li\u003e\n\u003cli\u003eDigital: Display \"- - -\", 1, check the temperature sensor 2 is missing or damaged, heating mode, high temperature protection 3, cryogenic cooling mode protection. In protected mode relay automatically disconnected.\u003c\/li\u003e\n\u003cli\u003eUse keys: temperature control panel has three buttons, button + button - SET button\u003c\/li\u003e\n\u003cli\u003eButton +: Achieving Rapid accumulation value\u003c\/li\u003e\n\u003cli\u003eKey: - fast diminishing value\u003c\/li\u003e\n\u003cli\u003eSET key SET: Temperature set temperature and operating mode interface query interface parameter setting interface\u003c\/li\u003e\n\u003cli\u003eDuring the SET press SET press according to different times, the corresponding digital temperature limit will be blinking, you can set the upper and lower temperature through the key addition and subtraction. After setting 8s automatically save data or short press three times data can be saved.\u003c\/li\u003e\n\u003cli\u003eSET Press to enter the actual temperature and the operating mode query interface, digital (on) the actual measured temperature. Digital (lower) showing the operation mode. L represents the lower limit temperature below the set temperature, H is the upper limit temperature is higher than the temperature setting, OFF indicates when the temperature is between the upper and lower limits, the relay is in the off state.\u003c\/li\u003e\n\u003cli\u003eMode setting: Setting the temperature 1: temperature upper limit set temperature 2: lower limit temperature\u003c\/li\u003e\n\u003cli\u003eExample applications: now the upper limit temperature to 40.0 ℃, the minimum temperature is set to 20.0 ℃. At different temperature ranges relay operate as follows:\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature\u0026gt; 40 ℃, the relay 1 is closed, the relay 2 release;\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature of 20 ℃ ≤ ≤40 ℃ release relay 1, relay 2 release;\u003c\/li\u003e\n\u003cli\u003eWhen the actual temperature \u0026lt;20 ℃, the relay 2 is closed, the relay 1 release.\u003c\/li\u003e\n\u003cli\u003eParameter settings: the need for the user parameter settings must first hold the SET button and then give the thermostat power, to enter the parameter setting interface. There are three sets of parameters P0-P2 can be used for user settings.\u003c\/li\u003e\n\u003cli\u003eParameter setting item\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003eFunction Description Setting range Factory setting\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eP0 temperature correction -10 ℃ ~ + 10 ℃ 0\u003c\/li\u003e\n\u003cli\u003eP1 limit relay time 0 ~ 999s OFF\u003c\/li\u003e\n\u003cli\u003eP2 lower limit relay time 0 ~ 999s OFF\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003efriendly reminder:\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003eP1 = OFF: indicates the actual temperature exceeds the upper limit temperature, corresponding relay will remain energized (long attracted state).\u003c\/li\u003e\n\u003cli\u003eP1 = 1 ~ 999: indicates the actual temperature exceeds the upper limit temperature, corresponding relay will energize long, then stop (Jog attracted state).\u003c\/li\u003e\n\u003cli\u003eP2 = OFF: indicates the actual temperature is below the lower limit temperature, corresponding relay will remain energized (long attracted state).\u003c\/li\u003e\n\u003cli\u003eP2 = 1 ~ 999: indicates the actual temperature is below the lower limit temperature, corresponding relay will energize long, then stop (Jog attracted state).\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cstrong\u003ePackage Inclued\u003c\/strong\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cli\u003e1PCS 12V Digital Dual Relay Alarm Thermometer Temperature Controller Air Regulator\u003c\/li\u003e\n\u003c\/ul\u003e"}