2.42" inch OLED Display RGB SSD1309 12864 SPI Serial Port for Arduino C51

2.42" inch OLED Display RGB SSD1309 12864 SPI Serial Port for Arduino C51

SKU:030526HU
Regular price $23.99

Features:

This is a 2.42 inch OLED display module of 128x64 resolution in which the emissive electroluminescent layer is a film of organic compound that emits light in response to an electric current.

Working without backlight, the OLED display module could give out light by itself.

In low ambient light conditions such as a dark room, an OLED screen can achieve a higher contrast ratio than an LCD.

OLED display module also has a much faster response time than an LCD.
The display with small dimension is suitable for MP3, function cellphone, smart health device, etc.

The seventh pin CS signal is leaded by default; If you do not need it, you can solder R18, then CS signal is directly grounded.

SPI communication or I2C communication can be switched by configuring three resistors R3 R4 R5.

As for IIC communication, it is necessary to move the resistor on R4 to R3, and R5 is soldered with 0 ohm resistor.


Product Introduction:
Size:2.42 inches
Resolution:128*64
Power supply voltage: 3.3V
Color: Green/White/Blue/Yellow


SPI Interface Definition:
GND:power ground
VCC:power positive
SCL:clock wire
SDA:data wire
RES:reset wire
DC:data/command
CS:chip selection

Package Include:
1 x 2.42" inch OLED Display SSD1309 128x64 SPI Serial Port for Arduino

trust seal
  • guaranteeQuality checked
  • Special gift cardsSpecial gift cards
  • Free return Within 60 days
  • Consultancy86-0755-85201155

Features:

This is a 2.42 inch OLED display module of 128x64 resolution in which the emissive electroluminescent layer is a film of organic compound that emits light in response to an electric current.

Working without backlight, the OLED display module could give out light by itself.

In low ambient light conditions such as a dark room, an OLED screen can achieve a higher contrast ratio than an LCD.

OLED display module also has a much faster response time than an LCD.
The display with small dimension is suitable for MP3, function cellphone, smart health device, etc.

The seventh pin CS signal is leaded by default; If you do not need it, you can solder R18, then CS signal is directly grounded.

SPI communication or I2C communication can be switched by configuring three resistors R3 R4 R5.

As for IIC communication, it is necessary to move the resistor on R4 to R3, and R5 is soldered with 0 ohm resistor.


Product Introduction:
Size:2.42 inches
Resolution:128*64
Power supply voltage: 3.3V
Color: Green/White/Blue/Yellow


SPI Interface Definition:
GND:power ground
VCC:power positive
SCL:clock wire
SDA:data wire
RES:reset wire
DC:data/command
CS:chip selection

Package Include:
1 x 2.42" inch OLED Display SSD1309 128x64 SPI Serial Port for Arduino

Purchasing & Delivery

Before you make your purchase, it’s helpful to know the measurements of the area you plan to place the furniture. You should also measure any doorways and hallways through which the furniture will pass to get to its final destination.
Picking up at the store
Shopify Shop requires that all products are properly inspected BEFORE you take it home to insure there are no surprises. Our team is happy to open all packages and will assist in the inspection process. We will then reseal packages for safe transport. We encourage all customers to bring furniture pads or blankets to protect the items during transport as well as rope or tie downs. Shopify Shop will not be responsible for damage that occurs after leaving the store or during transit. It is the purchaser’s responsibility to make sure the correct items are picked up and in good condition.
Delivery
Customers are able to pick the next available delivery day that best fits their schedule. However, to route stops as efficiently as possible, Shopify Shop will provide the time frame. Customers will not be able to choose a time. You will be notified in advance of your scheduled time frame. Please make sure that a responsible adult (18 years or older) will be home at that time.
In preparation for your delivery, please remove existing furniture, pictures, mirrors, accessories, etc. to prevent damages. Also insure that the area where you would like your furniture placed is clear of any old furniture and any other items that may obstruct the passageway of the delivery team. Shopify Shop will deliver, assemble, and set-up your new furniture purchase and remove all packing materials from your home. Our delivery crews are not permitted to move your existing furniture or other household items. Delivery personnel will attempt to deliver the purchased items in a safe and controlled manner but will not attempt to place furniture if they feel it will result in damage to the product or your home. Delivery personnel are unable to remove doors, hoist furniture or carry furniture up more than 3 flights of stairs. An elevator must be available for deliveries to the 4th floor and above.

Customer Reviews

No reviews yet Write a review