Digital Thermostat Heating Refrigeration Temperature Controller NTC10K Sensor
Digital Thermostat Heating Refrigeration Temperature Controller NTC10K Sensor
SKU:X12994
Regular price
$7.99
![]()
- guaranteeQuality checked
- Special gift cardsSpecial gift cards
- Free return Within 60 days
- Consultancy86-0755-85201155
Product Function:
Set Temperature ---- SetT;
Backlash Temperature-----BackT;
1. Heating Mode \'H\':
When Temperature ≤ SetT - BackT ;Relay conduction, heating equipment begin to work;
When Temperature ≥ SetT, Relay disconnect, heating equipment stop work;
2. Refrigeration mode \'C\':
When Temperature ≥ SetT + BackT ;Relay conduction, refrigeration equipment begin to work;
When Temperature ≤ SetT ;Relay conduction, refrigeration equipment stop work;
3. High Temperature Alarm \'ALA\':
When Temperature ≥ Alarm Temperature, The system opens the sound and light alarm, and disconnects the relay, any key stops the sound light;
4. Delay Start ‘OPH\':
When a normal heating or refrigeration work is done, the system starts to time T, and only after the T≥OPH, the system can carry out the next round of heating or refrigeration work;
5. Temperature Correction Function OFE(-10.0 ~ 10.0°):
The system will work for a long time and may have deviations that can be corrected by this function, Temperature = Measured + Calibration;
6. Parameter Remote Read/Set:
The parameters such as setting temperature, backlash temperature and temperature correction can be set through UART.
7. Real-time Temperature Report:
If the temperature reporting function is turned on, the product is transmitted to the terminal by the UART at 1s intervals, which facilitates data collection;
8. Relay enable (default enable):
If the relay is disable, the relay remains disconnected;
9. Restore factory Settings:
At the same time press the STOP, set key more than 3S, restore factory settings
Working mode setting /backlash temperature :
1. In the running interface, short press SET key, enter the Quick setting interface;
2. After entering the Quick Setup interface, switch the parameters
3. Through the UP DOWN key, modify the parameter value, support short press/long press;
4. Long press SET to build more than 3S or continuous 6S without any key operation, exit quickly set the interface, and save parameters;
Alarm temperature/delay Start /temperature correction:
1. In the operating interface, long press SET more than 3s, enter the parameters to set the interface;
2. Enter the parameter to set the interface, through the short press SET key to switch to set the parameters ;
3. through the UP DOWN key, modify the parameter value, support short press/long press;
4. Long press SET 3s above or continuous 6S without any key operation, exit parameter set interface, and save parameters;
How to turn on delay start (default 0ff):
Enter parameter setting interface, switch to alarm parameter OPH, turn on or off high temperature alarm function by short Press STOP button, if high temperature alarm function closes, OPH show \'----\' to remind;
Serial Control (MCU UART)
Communication standards:9600bps Data bits :8
Stop Bits :1
CRC :none
Flow control :none
Purchasing & Delivery
Before you make your purchase, it’s helpful to know the measurements of the area you plan to place the furniture. You should also measure any doorways and hallways through which the furniture will pass to get to its final destination.Picking up at the store
Shopify Shop requires that all products are properly inspected BEFORE you take it home to insure there are no surprises. Our team is happy to open all packages and will assist in the inspection process. We will then reseal packages for safe transport. We encourage all customers to bring furniture pads or blankets to protect the items during transport as well as rope or tie downs. Shopify Shop will not be responsible for damage that occurs after leaving the store or during transit. It is the purchaser’s responsibility to make sure the correct items are picked up and in good condition.Delivery
Customers are able to pick the next available delivery day that best fits their schedule. However, to route stops as efficiently as possible, Shopify Shop will provide the time frame. Customers will not be able to choose a time. You will be notified in advance of your scheduled time frame. Please make sure that a responsible adult (18 years or older) will be home at that time.In preparation for your delivery, please remove existing furniture, pictures, mirrors, accessories, etc. to prevent damages. Also insure that the area where you would like your furniture placed is clear of any old furniture and any other items that may obstruct the passageway of the delivery team. Shopify Shop will deliver, assemble, and set-up your new furniture purchase and remove all packing materials from your home. Our delivery crews are not permitted to move your existing furniture or other household items. Delivery personnel will attempt to deliver the purchased items in a safe and controlled manner but will not attempt to place furniture if they feel it will result in damage to the product or your home. Delivery personnel are unable to remove doors, hoist furniture or carry furniture up more than 3 flights of stairs. An elevator must be available for deliveries to the 4th floor and above.
Other Customers also buy:
-
Translation missing: en.products.product.regular_price $5.99{"id":4360815870023,"title":"Digital Thermostat Heating Refrigeration Temperature Controller NTC10K Sensor","handle":"xy-t01-dc6-30v-digital-thermostat-high-precision-digital-display-temperature-controller-module-refrigeration-heating-thermostat","description":"\u003cdiv class=\"detailmodule_html\"\u003e\n\u003cdiv class=\"detail-desc-decorate-richtext\"\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eProduct Function:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eSet Temperature ---- SetT;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eBacklash Temperature-----BackT;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. Heating Mode \\'H\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≤ SetT - BackT ;Relay conduction, heating equipment begin to work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ SetT, Relay disconnect, heating equipment stop work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. Refrigeration mode \\'C\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ SetT + BackT ;Relay conduction, refrigeration equipment begin to work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≤ SetT ;Relay conduction, refrigeration equipment stop work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. High Temperature Alarm \\'ALA\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ Alarm Temperature, The system opens the sound and light alarm, and disconnects the relay, any key stops the sound light;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Delay Start ‘OPH\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen a normal heating or refrigeration work is done, the system starts to time T, and only after the T≥OPH, the system can carry out the next round of heating or refrigeration work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e5. Temperature Correction Function OFE(-10.0 ~ 10.0°):\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eThe system will work for a long time and may have deviations that can be corrected by this function, Temperature = Measured + Calibration;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e6. Parameter Remote Read\/Set:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eThe parameters such as setting temperature, backlash temperature and temperature correction can be set through UART. \u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e7. Real-time Temperature Report:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eIf the temperature reporting function is turned on, the product is transmitted to the terminal by the UART at 1s intervals, which facilitates data collection;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e8. Relay enable (default enable):\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eIf the relay is disable, the relay remains disconnected;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e9. Restore factory Settings:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eAt the same time press the STOP, set key more than 3S, restore factory settings\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eWorking mode setting \/backlash temperature :\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. In the running interface, short press SET key, enter the Quick setting interface;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. After entering the Quick Setup interface, switch the parameters\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. Through the UP DOWN key, modify the parameter value, support short press\/long press;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Long press SET to build more than 3S or continuous 6S without any key operation, exit quickly set the interface, and save parameters;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eAlarm temperature\/delay Start \/temperature correction:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. In the operating interface, long press SET more than 3s, enter the parameters to set the interface;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. Enter the parameter to set the interface, through the short press SET key to switch to set the parameters ;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. through the UP DOWN key, modify the parameter value, support short press\/long press;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Long press SET 3s above or continuous 6S without any key operation, exit parameter set interface, and save parameters;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eHow to turn on delay start (default 0ff):\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eEnter parameter setting interface, switch to alarm parameter OPH, turn on or off high temperature alarm function by short Press STOP button, if high temperature alarm function closes, OPH show \\'----\\' to remind;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eSerial Control (MCU UART)\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eCommunication standards:9600bps Data bits :8\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eStop Bits :1\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eCRC :none\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eFlow control :none\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/ae01.alicdn.com\/kf\/Hf5179904a7c2457fbd45390fce86ce3aa.png\" class=\"detail-desc-decorate-image\" width=\"600\" height=\"303\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_5.png?v=1574073262\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_3.png?v=1574073253\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_2_db8bff04-2d6f-4d06-a7cb-8f7ea12bc85e.png?v=1574073244\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_1_5ebf7803-2a2d-47c5-aec4-54934afde267.png?v=1574073236\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003c\/div\u003e","published_at":"2019-11-18T18:14:08+08:00","created_at":"2019-11-18T18:36:51+08:00","vendor":"diymore","type":"Thermostat","tags":[],"price":799,"price_min":799,"price_max":799,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":31276277825607,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"X12994","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"Digital Thermostat Heating Refrigeration Temperature Controller NTC10K Sensor","public_title":null,"options":["Default Title"],"price":799,"weight":0,"compare_at_price":null,"inventory_management":null,"barcode":"","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_3_182.jpg?v=1588668433","\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_6_673.png?v=1588668433"],"featured_image":"\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_3_182.jpg?v=1588668433","options":["Title"],"media":[{"alt":"Xy-T01 Dc6-30V Digital Thermostat High Precision Display Temperature Controller Module Refrigeration","id":6679867523143,"position":1,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_3_182.jpg?v=1588668433"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_3_182.jpg?v=1588668433","width":1000},{"alt":"Xy-T01 Dc6-30V Digital Thermostat High Precision Display Temperature Controller Module Refrigeration","id":6679867719751,"position":2,"preview_image":{"aspect_ratio":1.111,"height":900,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_6_673.png?v=1588668433"},"aspect_ratio":1.111,"height":900,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_6_673.png?v=1588668433","width":1000}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cdiv class=\"detailmodule_html\"\u003e\n\u003cdiv class=\"detail-desc-decorate-richtext\"\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eProduct Function:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eSet Temperature ---- SetT;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eBacklash Temperature-----BackT;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. Heating Mode \\'H\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≤ SetT - BackT ;Relay conduction, heating equipment begin to work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ SetT, Relay disconnect, heating equipment stop work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. Refrigeration mode \\'C\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ SetT + BackT ;Relay conduction, refrigeration equipment begin to work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≤ SetT ;Relay conduction, refrigeration equipment stop work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. High Temperature Alarm \\'ALA\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ Alarm Temperature, The system opens the sound and light alarm, and disconnects the relay, any key stops the sound light;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Delay Start ‘OPH\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen a normal heating or refrigeration work is done, the system starts to time T, and only after the T≥OPH, the system can carry out the next round of heating or refrigeration work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e5. Temperature Correction Function OFE(-10.0 ~ 10.0°):\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eThe system will work for a long time and may have deviations that can be corrected by this function, Temperature = Measured + Calibration;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e6. Parameter Remote Read\/Set:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eThe parameters such as setting temperature, backlash temperature and temperature correction can be set through UART. \u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e7. Real-time Temperature Report:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eIf the temperature reporting function is turned on, the product is transmitted to the terminal by the UART at 1s intervals, which facilitates data collection;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e8. Relay enable (default enable):\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eIf the relay is disable, the relay remains disconnected;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e9. Restore factory Settings:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eAt the same time press the STOP, set key more than 3S, restore factory settings\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eWorking mode setting \/backlash temperature :\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. In the running interface, short press SET key, enter the Quick setting interface;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. After entering the Quick Setup interface, switch the parameters\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. Through the UP DOWN key, modify the parameter value, support short press\/long press;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Long press SET to build more than 3S or continuous 6S without any key operation, exit quickly set the interface, and save parameters;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eAlarm temperature\/delay Start \/temperature correction:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. In the operating interface, long press SET more than 3s, enter the parameters to set the interface;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. Enter the parameter to set the interface, through the short press SET key to switch to set the parameters ;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. through the UP DOWN key, modify the parameter value, support short press\/long press;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Long press SET 3s above or continuous 6S without any key operation, exit parameter set interface, and save parameters;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eHow to turn on delay start (default 0ff):\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eEnter parameter setting interface, switch to alarm parameter OPH, turn on or off high temperature alarm function by short Press STOP button, if high temperature alarm function closes, OPH show \\'----\\' to remind;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eSerial Control (MCU UART)\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eCommunication standards:9600bps Data bits :8\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eStop Bits :1\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eCRC :none\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eFlow control :none\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/ae01.alicdn.com\/kf\/Hf5179904a7c2457fbd45390fce86ce3aa.png\" class=\"detail-desc-decorate-image\" width=\"600\" height=\"303\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_5.png?v=1574073262\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_3.png?v=1574073253\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_2_db8bff04-2d6f-4d06-a7cb-8f7ea12bc85e.png?v=1574073244\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_1_5ebf7803-2a2d-47c5-aec4-54934afde267.png?v=1574073236\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003c\/div\u003e"} -
Translation missing: en.products.product.regular_price $5.99{"id":4360815870023,"title":"Digital Thermostat Heating Refrigeration Temperature Controller NTC10K Sensor","handle":"xy-t01-dc6-30v-digital-thermostat-high-precision-digital-display-temperature-controller-module-refrigeration-heating-thermostat","description":"\u003cdiv class=\"detailmodule_html\"\u003e\n\u003cdiv class=\"detail-desc-decorate-richtext\"\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eProduct Function:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eSet Temperature ---- SetT;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eBacklash Temperature-----BackT;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. Heating Mode \\'H\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≤ SetT - BackT ;Relay conduction, heating equipment begin to work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ SetT, Relay disconnect, heating equipment stop work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. Refrigeration mode \\'C\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ SetT + BackT ;Relay conduction, refrigeration equipment begin to work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≤ SetT ;Relay conduction, refrigeration equipment stop work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. High Temperature Alarm \\'ALA\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ Alarm Temperature, The system opens the sound and light alarm, and disconnects the relay, any key stops the sound light;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Delay Start ‘OPH\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen a normal heating or refrigeration work is done, the system starts to time T, and only after the T≥OPH, the system can carry out the next round of heating or refrigeration work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e5. Temperature Correction Function OFE(-10.0 ~ 10.0°):\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eThe system will work for a long time and may have deviations that can be corrected by this function, Temperature = Measured + Calibration;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e6. Parameter Remote Read\/Set:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eThe parameters such as setting temperature, backlash temperature and temperature correction can be set through UART. \u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e7. Real-time Temperature Report:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eIf the temperature reporting function is turned on, the product is transmitted to the terminal by the UART at 1s intervals, which facilitates data collection;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e8. Relay enable (default enable):\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eIf the relay is disable, the relay remains disconnected;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e9. Restore factory Settings:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eAt the same time press the STOP, set key more than 3S, restore factory settings\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eWorking mode setting \/backlash temperature :\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. In the running interface, short press SET key, enter the Quick setting interface;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. After entering the Quick Setup interface, switch the parameters\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. Through the UP DOWN key, modify the parameter value, support short press\/long press;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Long press SET to build more than 3S or continuous 6S without any key operation, exit quickly set the interface, and save parameters;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eAlarm temperature\/delay Start \/temperature correction:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. In the operating interface, long press SET more than 3s, enter the parameters to set the interface;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. Enter the parameter to set the interface, through the short press SET key to switch to set the parameters ;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. through the UP DOWN key, modify the parameter value, support short press\/long press;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Long press SET 3s above or continuous 6S without any key operation, exit parameter set interface, and save parameters;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eHow to turn on delay start (default 0ff):\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eEnter parameter setting interface, switch to alarm parameter OPH, turn on or off high temperature alarm function by short Press STOP button, if high temperature alarm function closes, OPH show \\'----\\' to remind;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eSerial Control (MCU UART)\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eCommunication standards:9600bps Data bits :8\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eStop Bits :1\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eCRC :none\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eFlow control :none\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/ae01.alicdn.com\/kf\/Hf5179904a7c2457fbd45390fce86ce3aa.png\" class=\"detail-desc-decorate-image\" width=\"600\" height=\"303\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_5.png?v=1574073262\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_3.png?v=1574073253\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_2_db8bff04-2d6f-4d06-a7cb-8f7ea12bc85e.png?v=1574073244\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_1_5ebf7803-2a2d-47c5-aec4-54934afde267.png?v=1574073236\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003c\/div\u003e","published_at":"2019-11-18T18:14:08+08:00","created_at":"2019-11-18T18:36:51+08:00","vendor":"diymore","type":"Thermostat","tags":[],"price":799,"price_min":799,"price_max":799,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":31276277825607,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"X12994","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"Digital Thermostat Heating Refrigeration Temperature Controller NTC10K Sensor","public_title":null,"options":["Default Title"],"price":799,"weight":0,"compare_at_price":null,"inventory_management":null,"barcode":"","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_3_182.jpg?v=1588668433","\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_6_673.png?v=1588668433"],"featured_image":"\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_3_182.jpg?v=1588668433","options":["Title"],"media":[{"alt":"Xy-T01 Dc6-30V Digital Thermostat High Precision Display Temperature Controller Module Refrigeration","id":6679867523143,"position":1,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_3_182.jpg?v=1588668433"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_3_182.jpg?v=1588668433","width":1000},{"alt":"Xy-T01 Dc6-30V Digital Thermostat High Precision Display Temperature Controller Module Refrigeration","id":6679867719751,"position":2,"preview_image":{"aspect_ratio":1.111,"height":900,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_6_673.png?v=1588668433"},"aspect_ratio":1.111,"height":900,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_6_673.png?v=1588668433","width":1000}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cdiv class=\"detailmodule_html\"\u003e\n\u003cdiv class=\"detail-desc-decorate-richtext\"\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eProduct Function:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eSet Temperature ---- SetT;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eBacklash Temperature-----BackT;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. Heating Mode \\'H\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≤ SetT - BackT ;Relay conduction, heating equipment begin to work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ SetT, Relay disconnect, heating equipment stop work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. Refrigeration mode \\'C\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ SetT + BackT ;Relay conduction, refrigeration equipment begin to work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≤ SetT ;Relay conduction, refrigeration equipment stop work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. High Temperature Alarm \\'ALA\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ Alarm Temperature, The system opens the sound and light alarm, and disconnects the relay, any key stops the sound light;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Delay Start ‘OPH\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen a normal heating or refrigeration work is done, the system starts to time T, and only after the T≥OPH, the system can carry out the next round of heating or refrigeration work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e5. Temperature Correction Function OFE(-10.0 ~ 10.0°):\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eThe system will work for a long time and may have deviations that can be corrected by this function, Temperature = Measured + Calibration;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e6. Parameter Remote Read\/Set:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eThe parameters such as setting temperature, backlash temperature and temperature correction can be set through UART. \u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e7. Real-time Temperature Report:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eIf the temperature reporting function is turned on, the product is transmitted to the terminal by the UART at 1s intervals, which facilitates data collection;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e8. Relay enable (default enable):\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eIf the relay is disable, the relay remains disconnected;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e9. Restore factory Settings:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eAt the same time press the STOP, set key more than 3S, restore factory settings\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eWorking mode setting \/backlash temperature :\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. In the running interface, short press SET key, enter the Quick setting interface;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. After entering the Quick Setup interface, switch the parameters\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. Through the UP DOWN key, modify the parameter value, support short press\/long press;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Long press SET to build more than 3S or continuous 6S without any key operation, exit quickly set the interface, and save parameters;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eAlarm temperature\/delay Start \/temperature correction:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. In the operating interface, long press SET more than 3s, enter the parameters to set the interface;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. Enter the parameter to set the interface, through the short press SET key to switch to set the parameters ;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. through the UP DOWN key, modify the parameter value, support short press\/long press;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Long press SET 3s above or continuous 6S without any key operation, exit parameter set interface, and save parameters;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eHow to turn on delay start (default 0ff):\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eEnter parameter setting interface, switch to alarm parameter OPH, turn on or off high temperature alarm function by short Press STOP button, if high temperature alarm function closes, OPH show \\'----\\' to remind;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eSerial Control (MCU UART)\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eCommunication standards:9600bps Data bits :8\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eStop Bits :1\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eCRC :none\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eFlow control :none\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/ae01.alicdn.com\/kf\/Hf5179904a7c2457fbd45390fce86ce3aa.png\" class=\"detail-desc-decorate-image\" width=\"600\" height=\"303\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_5.png?v=1574073262\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_3.png?v=1574073253\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_2_db8bff04-2d6f-4d06-a7cb-8f7ea12bc85e.png?v=1574073244\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_1_5ebf7803-2a2d-47c5-aec4-54934afde267.png?v=1574073236\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003c\/div\u003e"} -
Translation missing: en.products.product.regular_price $7.99{"id":4360815870023,"title":"Digital Thermostat Heating Refrigeration Temperature Controller NTC10K Sensor","handle":"xy-t01-dc6-30v-digital-thermostat-high-precision-digital-display-temperature-controller-module-refrigeration-heating-thermostat","description":"\u003cdiv class=\"detailmodule_html\"\u003e\n\u003cdiv class=\"detail-desc-decorate-richtext\"\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eProduct Function:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eSet Temperature ---- SetT;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eBacklash Temperature-----BackT;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. Heating Mode \\'H\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≤ SetT - BackT ;Relay conduction, heating equipment begin to work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ SetT, Relay disconnect, heating equipment stop work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. Refrigeration mode \\'C\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ SetT + BackT ;Relay conduction, refrigeration equipment begin to work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≤ SetT ;Relay conduction, refrigeration equipment stop work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. High Temperature Alarm \\'ALA\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ Alarm Temperature, The system opens the sound and light alarm, and disconnects the relay, any key stops the sound light;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Delay Start ‘OPH\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen a normal heating or refrigeration work is done, the system starts to time T, and only after the T≥OPH, the system can carry out the next round of heating or refrigeration work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e5. Temperature Correction Function OFE(-10.0 ~ 10.0°):\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eThe system will work for a long time and may have deviations that can be corrected by this function, Temperature = Measured + Calibration;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e6. Parameter Remote Read\/Set:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eThe parameters such as setting temperature, backlash temperature and temperature correction can be set through UART. \u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e7. Real-time Temperature Report:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eIf the temperature reporting function is turned on, the product is transmitted to the terminal by the UART at 1s intervals, which facilitates data collection;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e8. Relay enable (default enable):\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eIf the relay is disable, the relay remains disconnected;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e9. Restore factory Settings:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eAt the same time press the STOP, set key more than 3S, restore factory settings\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eWorking mode setting \/backlash temperature :\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. In the running interface, short press SET key, enter the Quick setting interface;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. After entering the Quick Setup interface, switch the parameters\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. Through the UP DOWN key, modify the parameter value, support short press\/long press;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Long press SET to build more than 3S or continuous 6S without any key operation, exit quickly set the interface, and save parameters;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eAlarm temperature\/delay Start \/temperature correction:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. In the operating interface, long press SET more than 3s, enter the parameters to set the interface;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. Enter the parameter to set the interface, through the short press SET key to switch to set the parameters ;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. through the UP DOWN key, modify the parameter value, support short press\/long press;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Long press SET 3s above or continuous 6S without any key operation, exit parameter set interface, and save parameters;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eHow to turn on delay start (default 0ff):\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eEnter parameter setting interface, switch to alarm parameter OPH, turn on or off high temperature alarm function by short Press STOP button, if high temperature alarm function closes, OPH show \\'----\\' to remind;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eSerial Control (MCU UART)\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eCommunication standards:9600bps Data bits :8\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eStop Bits :1\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eCRC :none\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eFlow control :none\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/ae01.alicdn.com\/kf\/Hf5179904a7c2457fbd45390fce86ce3aa.png\" class=\"detail-desc-decorate-image\" width=\"600\" height=\"303\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_5.png?v=1574073262\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_3.png?v=1574073253\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_2_db8bff04-2d6f-4d06-a7cb-8f7ea12bc85e.png?v=1574073244\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_1_5ebf7803-2a2d-47c5-aec4-54934afde267.png?v=1574073236\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003c\/div\u003e","published_at":"2019-11-18T18:14:08+08:00","created_at":"2019-11-18T18:36:51+08:00","vendor":"diymore","type":"Thermostat","tags":[],"price":799,"price_min":799,"price_max":799,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":31276277825607,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"X12994","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"Digital Thermostat Heating Refrigeration Temperature Controller NTC10K Sensor","public_title":null,"options":["Default Title"],"price":799,"weight":0,"compare_at_price":null,"inventory_management":null,"barcode":"","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_3_182.jpg?v=1588668433","\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_6_673.png?v=1588668433"],"featured_image":"\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_3_182.jpg?v=1588668433","options":["Title"],"media":[{"alt":"Xy-T01 Dc6-30V Digital Thermostat High Precision Display Temperature Controller Module Refrigeration","id":6679867523143,"position":1,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_3_182.jpg?v=1588668433"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_3_182.jpg?v=1588668433","width":1000},{"alt":"Xy-T01 Dc6-30V Digital Thermostat High Precision Display Temperature Controller Module Refrigeration","id":6679867719751,"position":2,"preview_image":{"aspect_ratio":1.111,"height":900,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_6_673.png?v=1588668433"},"aspect_ratio":1.111,"height":900,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_6_673.png?v=1588668433","width":1000}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cdiv class=\"detailmodule_html\"\u003e\n\u003cdiv class=\"detail-desc-decorate-richtext\"\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eProduct Function:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eSet Temperature ---- SetT;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eBacklash Temperature-----BackT;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. Heating Mode \\'H\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≤ SetT - BackT ;Relay conduction, heating equipment begin to work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ SetT, Relay disconnect, heating equipment stop work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. Refrigeration mode \\'C\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ SetT + BackT ;Relay conduction, refrigeration equipment begin to work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≤ SetT ;Relay conduction, refrigeration equipment stop work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. High Temperature Alarm \\'ALA\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ Alarm Temperature, The system opens the sound and light alarm, and disconnects the relay, any key stops the sound light;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Delay Start ‘OPH\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen a normal heating or refrigeration work is done, the system starts to time T, and only after the T≥OPH, the system can carry out the next round of heating or refrigeration work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e5. Temperature Correction Function OFE(-10.0 ~ 10.0°):\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eThe system will work for a long time and may have deviations that can be corrected by this function, Temperature = Measured + Calibration;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e6. Parameter Remote Read\/Set:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eThe parameters such as setting temperature, backlash temperature and temperature correction can be set through UART. \u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e7. Real-time Temperature Report:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eIf the temperature reporting function is turned on, the product is transmitted to the terminal by the UART at 1s intervals, which facilitates data collection;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e8. Relay enable (default enable):\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eIf the relay is disable, the relay remains disconnected;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e9. Restore factory Settings:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eAt the same time press the STOP, set key more than 3S, restore factory settings\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eWorking mode setting \/backlash temperature :\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. In the running interface, short press SET key, enter the Quick setting interface;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. After entering the Quick Setup interface, switch the parameters\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. Through the UP DOWN key, modify the parameter value, support short press\/long press;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Long press SET to build more than 3S or continuous 6S without any key operation, exit quickly set the interface, and save parameters;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eAlarm temperature\/delay Start \/temperature correction:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. In the operating interface, long press SET more than 3s, enter the parameters to set the interface;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. Enter the parameter to set the interface, through the short press SET key to switch to set the parameters ;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. through the UP DOWN key, modify the parameter value, support short press\/long press;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Long press SET 3s above or continuous 6S without any key operation, exit parameter set interface, and save parameters;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eHow to turn on delay start (default 0ff):\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eEnter parameter setting interface, switch to alarm parameter OPH, turn on or off high temperature alarm function by short Press STOP button, if high temperature alarm function closes, OPH show \\'----\\' to remind;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eSerial Control (MCU UART)\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eCommunication standards:9600bps Data bits :8\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eStop Bits :1\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eCRC :none\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eFlow control :none\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/ae01.alicdn.com\/kf\/Hf5179904a7c2457fbd45390fce86ce3aa.png\" class=\"detail-desc-decorate-image\" width=\"600\" height=\"303\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_5.png?v=1574073262\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_3.png?v=1574073253\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_2_db8bff04-2d6f-4d06-a7cb-8f7ea12bc85e.png?v=1574073244\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_1_5ebf7803-2a2d-47c5-aec4-54934afde267.png?v=1574073236\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003c\/div\u003e"} -
Translation missing: en.products.product.regular_price $9.99{"id":4360815870023,"title":"Digital Thermostat Heating Refrigeration Temperature Controller NTC10K Sensor","handle":"xy-t01-dc6-30v-digital-thermostat-high-precision-digital-display-temperature-controller-module-refrigeration-heating-thermostat","description":"\u003cdiv class=\"detailmodule_html\"\u003e\n\u003cdiv class=\"detail-desc-decorate-richtext\"\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eProduct Function:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eSet Temperature ---- SetT;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eBacklash Temperature-----BackT;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. Heating Mode \\'H\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≤ SetT - BackT ;Relay conduction, heating equipment begin to work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ SetT, Relay disconnect, heating equipment stop work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. Refrigeration mode \\'C\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ SetT + BackT ;Relay conduction, refrigeration equipment begin to work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≤ SetT ;Relay conduction, refrigeration equipment stop work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. High Temperature Alarm \\'ALA\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ Alarm Temperature, The system opens the sound and light alarm, and disconnects the relay, any key stops the sound light;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Delay Start ‘OPH\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen a normal heating or refrigeration work is done, the system starts to time T, and only after the T≥OPH, the system can carry out the next round of heating or refrigeration work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e5. Temperature Correction Function OFE(-10.0 ~ 10.0°):\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eThe system will work for a long time and may have deviations that can be corrected by this function, Temperature = Measured + Calibration;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e6. Parameter Remote Read\/Set:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eThe parameters such as setting temperature, backlash temperature and temperature correction can be set through UART. \u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e7. Real-time Temperature Report:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eIf the temperature reporting function is turned on, the product is transmitted to the terminal by the UART at 1s intervals, which facilitates data collection;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e8. Relay enable (default enable):\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eIf the relay is disable, the relay remains disconnected;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e9. Restore factory Settings:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eAt the same time press the STOP, set key more than 3S, restore factory settings\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eWorking mode setting \/backlash temperature :\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. In the running interface, short press SET key, enter the Quick setting interface;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. After entering the Quick Setup interface, switch the parameters\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. Through the UP DOWN key, modify the parameter value, support short press\/long press;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Long press SET to build more than 3S or continuous 6S without any key operation, exit quickly set the interface, and save parameters;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eAlarm temperature\/delay Start \/temperature correction:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. In the operating interface, long press SET more than 3s, enter the parameters to set the interface;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. Enter the parameter to set the interface, through the short press SET key to switch to set the parameters ;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. through the UP DOWN key, modify the parameter value, support short press\/long press;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Long press SET 3s above or continuous 6S without any key operation, exit parameter set interface, and save parameters;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eHow to turn on delay start (default 0ff):\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eEnter parameter setting interface, switch to alarm parameter OPH, turn on or off high temperature alarm function by short Press STOP button, if high temperature alarm function closes, OPH show \\'----\\' to remind;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eSerial Control (MCU UART)\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eCommunication standards:9600bps Data bits :8\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eStop Bits :1\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eCRC :none\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eFlow control :none\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/ae01.alicdn.com\/kf\/Hf5179904a7c2457fbd45390fce86ce3aa.png\" class=\"detail-desc-decorate-image\" width=\"600\" height=\"303\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_5.png?v=1574073262\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_3.png?v=1574073253\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_2_db8bff04-2d6f-4d06-a7cb-8f7ea12bc85e.png?v=1574073244\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_1_5ebf7803-2a2d-47c5-aec4-54934afde267.png?v=1574073236\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003c\/div\u003e","published_at":"2019-11-18T18:14:08+08:00","created_at":"2019-11-18T18:36:51+08:00","vendor":"diymore","type":"Thermostat","tags":[],"price":799,"price_min":799,"price_max":799,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":31276277825607,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"X12994","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"Digital Thermostat Heating Refrigeration Temperature Controller NTC10K Sensor","public_title":null,"options":["Default Title"],"price":799,"weight":0,"compare_at_price":null,"inventory_management":null,"barcode":"","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_3_182.jpg?v=1588668433","\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_6_673.png?v=1588668433"],"featured_image":"\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_3_182.jpg?v=1588668433","options":["Title"],"media":[{"alt":"Xy-T01 Dc6-30V Digital Thermostat High Precision Display Temperature Controller Module Refrigeration","id":6679867523143,"position":1,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_3_182.jpg?v=1588668433"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_3_182.jpg?v=1588668433","width":1000},{"alt":"Xy-T01 Dc6-30V Digital Thermostat High Precision Display Temperature Controller Module Refrigeration","id":6679867719751,"position":2,"preview_image":{"aspect_ratio":1.111,"height":900,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_6_673.png?v=1588668433"},"aspect_ratio":1.111,"height":900,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_6_673.png?v=1588668433","width":1000}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cdiv class=\"detailmodule_html\"\u003e\n\u003cdiv class=\"detail-desc-decorate-richtext\"\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eProduct Function:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eSet Temperature ---- SetT;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eBacklash Temperature-----BackT;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. Heating Mode \\'H\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≤ SetT - BackT ;Relay conduction, heating equipment begin to work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ SetT, Relay disconnect, heating equipment stop work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. Refrigeration mode \\'C\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ SetT + BackT ;Relay conduction, refrigeration equipment begin to work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≤ SetT ;Relay conduction, refrigeration equipment stop work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. High Temperature Alarm \\'ALA\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ Alarm Temperature, The system opens the sound and light alarm, and disconnects the relay, any key stops the sound light;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Delay Start ‘OPH\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen a normal heating or refrigeration work is done, the system starts to time T, and only after the T≥OPH, the system can carry out the next round of heating or refrigeration work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e5. Temperature Correction Function OFE(-10.0 ~ 10.0°):\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eThe system will work for a long time and may have deviations that can be corrected by this function, Temperature = Measured + Calibration;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e6. Parameter Remote Read\/Set:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eThe parameters such as setting temperature, backlash temperature and temperature correction can be set through UART. \u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e7. Real-time Temperature Report:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eIf the temperature reporting function is turned on, the product is transmitted to the terminal by the UART at 1s intervals, which facilitates data collection;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e8. Relay enable (default enable):\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eIf the relay is disable, the relay remains disconnected;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e9. Restore factory Settings:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eAt the same time press the STOP, set key more than 3S, restore factory settings\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eWorking mode setting \/backlash temperature :\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. In the running interface, short press SET key, enter the Quick setting interface;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. After entering the Quick Setup interface, switch the parameters\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. Through the UP DOWN key, modify the parameter value, support short press\/long press;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Long press SET to build more than 3S or continuous 6S without any key operation, exit quickly set the interface, and save parameters;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eAlarm temperature\/delay Start \/temperature correction:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. In the operating interface, long press SET more than 3s, enter the parameters to set the interface;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. Enter the parameter to set the interface, through the short press SET key to switch to set the parameters ;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. through the UP DOWN key, modify the parameter value, support short press\/long press;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Long press SET 3s above or continuous 6S without any key operation, exit parameter set interface, and save parameters;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eHow to turn on delay start (default 0ff):\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eEnter parameter setting interface, switch to alarm parameter OPH, turn on or off high temperature alarm function by short Press STOP button, if high temperature alarm function closes, OPH show \\'----\\' to remind;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eSerial Control (MCU UART)\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eCommunication standards:9600bps Data bits :8\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eStop Bits :1\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eCRC :none\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eFlow control :none\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/ae01.alicdn.com\/kf\/Hf5179904a7c2457fbd45390fce86ce3aa.png\" class=\"detail-desc-decorate-image\" width=\"600\" height=\"303\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_5.png?v=1574073262\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_3.png?v=1574073253\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_2_db8bff04-2d6f-4d06-a7cb-8f7ea12bc85e.png?v=1574073244\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_1_5ebf7803-2a2d-47c5-aec4-54934afde267.png?v=1574073236\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003c\/div\u003e"} -
Translation missing: en.products.product.regular_price $5.99{"id":4360815870023,"title":"Digital Thermostat Heating Refrigeration Temperature Controller NTC10K Sensor","handle":"xy-t01-dc6-30v-digital-thermostat-high-precision-digital-display-temperature-controller-module-refrigeration-heating-thermostat","description":"\u003cdiv class=\"detailmodule_html\"\u003e\n\u003cdiv class=\"detail-desc-decorate-richtext\"\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eProduct Function:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eSet Temperature ---- SetT;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eBacklash Temperature-----BackT;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. Heating Mode \\'H\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≤ SetT - BackT ;Relay conduction, heating equipment begin to work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ SetT, Relay disconnect, heating equipment stop work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. Refrigeration mode \\'C\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ SetT + BackT ;Relay conduction, refrigeration equipment begin to work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≤ SetT ;Relay conduction, refrigeration equipment stop work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. High Temperature Alarm \\'ALA\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ Alarm Temperature, The system opens the sound and light alarm, and disconnects the relay, any key stops the sound light;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Delay Start ‘OPH\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen a normal heating or refrigeration work is done, the system starts to time T, and only after the T≥OPH, the system can carry out the next round of heating or refrigeration work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e5. Temperature Correction Function OFE(-10.0 ~ 10.0°):\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eThe system will work for a long time and may have deviations that can be corrected by this function, Temperature = Measured + Calibration;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e6. Parameter Remote Read\/Set:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eThe parameters such as setting temperature, backlash temperature and temperature correction can be set through UART. \u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e7. Real-time Temperature Report:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eIf the temperature reporting function is turned on, the product is transmitted to the terminal by the UART at 1s intervals, which facilitates data collection;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e8. Relay enable (default enable):\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eIf the relay is disable, the relay remains disconnected;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e9. Restore factory Settings:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eAt the same time press the STOP, set key more than 3S, restore factory settings\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eWorking mode setting \/backlash temperature :\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. In the running interface, short press SET key, enter the Quick setting interface;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. After entering the Quick Setup interface, switch the parameters\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. Through the UP DOWN key, modify the parameter value, support short press\/long press;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Long press SET to build more than 3S or continuous 6S without any key operation, exit quickly set the interface, and save parameters;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eAlarm temperature\/delay Start \/temperature correction:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. In the operating interface, long press SET more than 3s, enter the parameters to set the interface;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. Enter the parameter to set the interface, through the short press SET key to switch to set the parameters ;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. through the UP DOWN key, modify the parameter value, support short press\/long press;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Long press SET 3s above or continuous 6S without any key operation, exit parameter set interface, and save parameters;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eHow to turn on delay start (default 0ff):\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eEnter parameter setting interface, switch to alarm parameter OPH, turn on or off high temperature alarm function by short Press STOP button, if high temperature alarm function closes, OPH show \\'----\\' to remind;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eSerial Control (MCU UART)\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eCommunication standards:9600bps Data bits :8\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eStop Bits :1\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eCRC :none\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eFlow control :none\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/ae01.alicdn.com\/kf\/Hf5179904a7c2457fbd45390fce86ce3aa.png\" class=\"detail-desc-decorate-image\" width=\"600\" height=\"303\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_5.png?v=1574073262\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_3.png?v=1574073253\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_2_db8bff04-2d6f-4d06-a7cb-8f7ea12bc85e.png?v=1574073244\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_1_5ebf7803-2a2d-47c5-aec4-54934afde267.png?v=1574073236\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003c\/div\u003e","published_at":"2019-11-18T18:14:08+08:00","created_at":"2019-11-18T18:36:51+08:00","vendor":"diymore","type":"Thermostat","tags":[],"price":799,"price_min":799,"price_max":799,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":31276277825607,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"X12994","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"Digital Thermostat Heating Refrigeration Temperature Controller NTC10K Sensor","public_title":null,"options":["Default Title"],"price":799,"weight":0,"compare_at_price":null,"inventory_management":null,"barcode":"","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_3_182.jpg?v=1588668433","\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_6_673.png?v=1588668433"],"featured_image":"\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_3_182.jpg?v=1588668433","options":["Title"],"media":[{"alt":"Xy-T01 Dc6-30V Digital Thermostat High Precision Display Temperature Controller Module Refrigeration","id":6679867523143,"position":1,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_3_182.jpg?v=1588668433"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_3_182.jpg?v=1588668433","width":1000},{"alt":"Xy-T01 Dc6-30V Digital Thermostat High Precision Display Temperature Controller Module Refrigeration","id":6679867719751,"position":2,"preview_image":{"aspect_ratio":1.111,"height":900,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_6_673.png?v=1588668433"},"aspect_ratio":1.111,"height":900,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_6_673.png?v=1588668433","width":1000}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cdiv class=\"detailmodule_html\"\u003e\n\u003cdiv class=\"detail-desc-decorate-richtext\"\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eProduct Function:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eSet Temperature ---- SetT;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eBacklash Temperature-----BackT;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. Heating Mode \\'H\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≤ SetT - BackT ;Relay conduction, heating equipment begin to work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ SetT, Relay disconnect, heating equipment stop work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. Refrigeration mode \\'C\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ SetT + BackT ;Relay conduction, refrigeration equipment begin to work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≤ SetT ;Relay conduction, refrigeration equipment stop work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. High Temperature Alarm \\'ALA\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ Alarm Temperature, The system opens the sound and light alarm, and disconnects the relay, any key stops the sound light;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Delay Start ‘OPH\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen a normal heating or refrigeration work is done, the system starts to time T, and only after the T≥OPH, the system can carry out the next round of heating or refrigeration work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e5. Temperature Correction Function OFE(-10.0 ~ 10.0°):\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eThe system will work for a long time and may have deviations that can be corrected by this function, Temperature = Measured + Calibration;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e6. Parameter Remote Read\/Set:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eThe parameters such as setting temperature, backlash temperature and temperature correction can be set through UART. \u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e7. Real-time Temperature Report:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eIf the temperature reporting function is turned on, the product is transmitted to the terminal by the UART at 1s intervals, which facilitates data collection;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e8. Relay enable (default enable):\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eIf the relay is disable, the relay remains disconnected;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e9. Restore factory Settings:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eAt the same time press the STOP, set key more than 3S, restore factory settings\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eWorking mode setting \/backlash temperature :\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. In the running interface, short press SET key, enter the Quick setting interface;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. After entering the Quick Setup interface, switch the parameters\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. Through the UP DOWN key, modify the parameter value, support short press\/long press;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Long press SET to build more than 3S or continuous 6S without any key operation, exit quickly set the interface, and save parameters;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eAlarm temperature\/delay Start \/temperature correction:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. In the operating interface, long press SET more than 3s, enter the parameters to set the interface;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. Enter the parameter to set the interface, through the short press SET key to switch to set the parameters ;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. through the UP DOWN key, modify the parameter value, support short press\/long press;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Long press SET 3s above or continuous 6S without any key operation, exit parameter set interface, and save parameters;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eHow to turn on delay start (default 0ff):\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eEnter parameter setting interface, switch to alarm parameter OPH, turn on or off high temperature alarm function by short Press STOP button, if high temperature alarm function closes, OPH show \\'----\\' to remind;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eSerial Control (MCU UART)\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eCommunication standards:9600bps Data bits :8\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eStop Bits :1\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eCRC :none\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eFlow control :none\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/ae01.alicdn.com\/kf\/Hf5179904a7c2457fbd45390fce86ce3aa.png\" class=\"detail-desc-decorate-image\" width=\"600\" height=\"303\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_5.png?v=1574073262\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_3.png?v=1574073253\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_2_db8bff04-2d6f-4d06-a7cb-8f7ea12bc85e.png?v=1574073244\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_1_5ebf7803-2a2d-47c5-aec4-54934afde267.png?v=1574073236\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003c\/div\u003e"} -
Translation missing: en.products.product.regular_price $8.99{"id":4360815870023,"title":"Digital Thermostat Heating Refrigeration Temperature Controller NTC10K Sensor","handle":"xy-t01-dc6-30v-digital-thermostat-high-precision-digital-display-temperature-controller-module-refrigeration-heating-thermostat","description":"\u003cdiv class=\"detailmodule_html\"\u003e\n\u003cdiv class=\"detail-desc-decorate-richtext\"\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eProduct Function:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eSet Temperature ---- SetT;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eBacklash Temperature-----BackT;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. Heating Mode \\'H\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≤ SetT - BackT ;Relay conduction, heating equipment begin to work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ SetT, Relay disconnect, heating equipment stop work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. Refrigeration mode \\'C\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ SetT + BackT ;Relay conduction, refrigeration equipment begin to work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≤ SetT ;Relay conduction, refrigeration equipment stop work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. High Temperature Alarm \\'ALA\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ Alarm Temperature, The system opens the sound and light alarm, and disconnects the relay, any key stops the sound light;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Delay Start ‘OPH\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen a normal heating or refrigeration work is done, the system starts to time T, and only after the T≥OPH, the system can carry out the next round of heating or refrigeration work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e5. Temperature Correction Function OFE(-10.0 ~ 10.0°):\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eThe system will work for a long time and may have deviations that can be corrected by this function, Temperature = Measured + Calibration;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e6. Parameter Remote Read\/Set:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eThe parameters such as setting temperature, backlash temperature and temperature correction can be set through UART. \u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e7. Real-time Temperature Report:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eIf the temperature reporting function is turned on, the product is transmitted to the terminal by the UART at 1s intervals, which facilitates data collection;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e8. Relay enable (default enable):\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eIf the relay is disable, the relay remains disconnected;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e9. Restore factory Settings:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eAt the same time press the STOP, set key more than 3S, restore factory settings\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eWorking mode setting \/backlash temperature :\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. In the running interface, short press SET key, enter the Quick setting interface;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. After entering the Quick Setup interface, switch the parameters\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. Through the UP DOWN key, modify the parameter value, support short press\/long press;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Long press SET to build more than 3S or continuous 6S without any key operation, exit quickly set the interface, and save parameters;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eAlarm temperature\/delay Start \/temperature correction:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. In the operating interface, long press SET more than 3s, enter the parameters to set the interface;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. Enter the parameter to set the interface, through the short press SET key to switch to set the parameters ;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. through the UP DOWN key, modify the parameter value, support short press\/long press;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Long press SET 3s above or continuous 6S without any key operation, exit parameter set interface, and save parameters;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eHow to turn on delay start (default 0ff):\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eEnter parameter setting interface, switch to alarm parameter OPH, turn on or off high temperature alarm function by short Press STOP button, if high temperature alarm function closes, OPH show \\'----\\' to remind;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eSerial Control (MCU UART)\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eCommunication standards:9600bps Data bits :8\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eStop Bits :1\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eCRC :none\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eFlow control :none\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/ae01.alicdn.com\/kf\/Hf5179904a7c2457fbd45390fce86ce3aa.png\" class=\"detail-desc-decorate-image\" width=\"600\" height=\"303\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_5.png?v=1574073262\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_3.png?v=1574073253\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_2_db8bff04-2d6f-4d06-a7cb-8f7ea12bc85e.png?v=1574073244\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_1_5ebf7803-2a2d-47c5-aec4-54934afde267.png?v=1574073236\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003c\/div\u003e","published_at":"2019-11-18T18:14:08+08:00","created_at":"2019-11-18T18:36:51+08:00","vendor":"diymore","type":"Thermostat","tags":[],"price":799,"price_min":799,"price_max":799,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":31276277825607,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"X12994","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"Digital Thermostat Heating Refrigeration Temperature Controller NTC10K Sensor","public_title":null,"options":["Default Title"],"price":799,"weight":0,"compare_at_price":null,"inventory_management":null,"barcode":"","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_3_182.jpg?v=1588668433","\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_6_673.png?v=1588668433"],"featured_image":"\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_3_182.jpg?v=1588668433","options":["Title"],"media":[{"alt":"Xy-T01 Dc6-30V Digital Thermostat High Precision Display Temperature Controller Module Refrigeration","id":6679867523143,"position":1,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_3_182.jpg?v=1588668433"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_3_182.jpg?v=1588668433","width":1000},{"alt":"Xy-T01 Dc6-30V Digital Thermostat High Precision Display Temperature Controller Module Refrigeration","id":6679867719751,"position":2,"preview_image":{"aspect_ratio":1.111,"height":900,"width":1000,"src":"\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_6_673.png?v=1588668433"},"aspect_ratio":1.111,"height":900,"media_type":"image","src":"\/\/www.diymore.cc\/cdn\/shop\/products\/X12994_6_673.png?v=1588668433","width":1000}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cdiv class=\"detailmodule_html\"\u003e\n\u003cdiv class=\"detail-desc-decorate-richtext\"\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eProduct Function:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eSet Temperature ---- SetT;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eBacklash Temperature-----BackT;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. Heating Mode \\'H\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≤ SetT - BackT ;Relay conduction, heating equipment begin to work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ SetT, Relay disconnect, heating equipment stop work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. Refrigeration mode \\'C\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ SetT + BackT ;Relay conduction, refrigeration equipment begin to work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≤ SetT ;Relay conduction, refrigeration equipment stop work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. High Temperature Alarm \\'ALA\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen Temperature ≥ Alarm Temperature, The system opens the sound and light alarm, and disconnects the relay, any key stops the sound light;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Delay Start ‘OPH\\':\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eWhen a normal heating or refrigeration work is done, the system starts to time T, and only after the T≥OPH, the system can carry out the next round of heating or refrigeration work;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e5. Temperature Correction Function OFE(-10.0 ~ 10.0°):\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eThe system will work for a long time and may have deviations that can be corrected by this function, Temperature = Measured + Calibration;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e6. Parameter Remote Read\/Set:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eThe parameters such as setting temperature, backlash temperature and temperature correction can be set through UART. \u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e7. Real-time Temperature Report:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eIf the temperature reporting function is turned on, the product is transmitted to the terminal by the UART at 1s intervals, which facilitates data collection;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e8. Relay enable (default enable):\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eIf the relay is disable, the relay remains disconnected;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e9. Restore factory Settings:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eAt the same time press the STOP, set key more than 3S, restore factory settings\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eWorking mode setting \/backlash temperature :\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. In the running interface, short press SET key, enter the Quick setting interface;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. After entering the Quick Setup interface, switch the parameters\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. Through the UP DOWN key, modify the parameter value, support short press\/long press;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Long press SET to build more than 3S or continuous 6S without any key operation, exit quickly set the interface, and save parameters;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eAlarm temperature\/delay Start \/temperature correction:\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e1. In the operating interface, long press SET more than 3s, enter the parameters to set the interface;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e2. Enter the parameter to set the interface, through the short press SET key to switch to set the parameters ;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e3. through the UP DOWN key, modify the parameter value, support short press\/long press;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e4. Long press SET 3s above or continuous 6S without any key operation, exit parameter set interface, and save parameters;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003e\u003cstrong\u003eHow to turn on delay start (default 0ff):\u003c\/strong\u003e\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eEnter parameter setting interface, switch to alarm parameter OPH, turn on or off high temperature alarm function by short Press STOP button, if high temperature alarm function closes, OPH show \\'----\\' to remind;\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e \u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eSerial Control (MCU UART)\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eCommunication standards:9600bps Data bits :8\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eStop Bits :1\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eCRC :none\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan\u003eFlow control :none\u003c\/span\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/ae01.alicdn.com\/kf\/Hf5179904a7c2457fbd45390fce86ce3aa.png\" class=\"detail-desc-decorate-image\" width=\"600\" height=\"303\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_5.png?v=1574073262\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_3.png?v=1574073253\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_2_db8bff04-2d6f-4d06-a7cb-8f7ea12bc85e.png?v=1574073244\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/files\/X12994_1_5ebf7803-2a2d-47c5-aec4-54934afde267.png?v=1574073236\" alt=\"\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"detailmodule_image\"\u003e\u003c\/div\u003e"}
